A 250 mm Fig. P4.22 250 mm D 200 mm 30° B 500 N 4.22 A lever AB is hinged at C and attached to a control cable at A. If the lever is subjected to a 500-N horizontal force at B, determine (a) the tension in the cable, (b) the reaction at C.

Q: Find the shape factor of following T section.

A:

Q: The solid shown consists of a solid cylinder and a hemisphere. Use composite shapes to determine the…

A: Given data,  A composite Solid section,  Radius of cylinder = 30in. Radius of hemisphere = 30in.…

Q: The uniform wire is bent into the shape shown and held by the frictionless pin at O. Determine the…

A: It is given that,

Q: Q3: Consider a two degree of freedom bar elements as shown in figure. Using finite element method to…

A: Consider the free body diagram;

Q: 1: Mechanics Resolve force in X direction Force applied=100 N Angle with horizontal is 60 degree

A: Given data : The value of applied force F=100 N The value of angle with horizontal θ=60∘   Required…

Q: du - 2ry = x, with y(0) = 0- %3D %3D

A:

Q: 1. A line having an equation of y = 2x intersects the curve y² = 8x. Compute the centroid.

A: to find centroid

Q: Two forces acting on a particle can be replaced by the resultant by drawing diagonal of the O a.…

A: Option A is right

Q: An I-section beam ABC has a constant EI and is loaded as shown in the figure below. This beam has a…

A: Note : As per bartleby guidelines, only first 3 subparts can be solved. For rest of the parts,…

Q: ep in digital format plea

A:

Q: Problem II. From a triangular steel plate XYZ, a triangular section VwZ was cleanly cut off. What…

A: Given data:

Q: PROBLEM 1 For the area shown, do the following: a. Determine the centroid with respect to the…

A:

Q: a Find the distance x between the points (1,4) and (5, –8).

A: Distance X between two points is calculated as follow

Q: An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure.…

A: stresses on an element is given as followschange in length of diagonal BD=?

Q: Determine the coordinates of the centroid of the trapezoidal area shown. Assume a = 275 mm, b= 485…

A: The given figure is:

Q: The truss shown is one of several supporting an advertising panel. Consider the wind load P = 820 N…

A: Step 1:Step 2:Step 3:Step 4:

Q: Find the shape factor of following T section.

A: Determine the shape factor of the given T section.

Q: 5. Determine the x component of the centroid of the given area. y A 2 y = x y=1.44-x B X

A: we have given equations y2 = x  , y = 1.44 - x    At mid of the given area, point C…

Q: orce A=25 N A B=30 N

A: On the left side, tan(theta) = Perpendicular/base  tan(theta) = 7/4 = 1.75 angle theta = tan inverse…

Q: While cutting a piece of paper, a person exerts the two indicated forces on a paper cutter. Reduce…

A: Solution; Given that; Dimension of paper cutter=30"×30"

Q: If a=100 inch, b=52 inch and C=60 degrees find c

A: To determine the third side (c) of a triangle provided we have, the other two sides (a and b) and…

Q: *.To obtain parallel lines, concentric circles and parallel curves is used Mirror Extend Offset non…

A:

Q: Find the centroid.

A:

Q: Determine me 1. Locate the centroid of the bent wire shown in the figure. The wire is homogenous and…

A:

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: P=110 N

Q: Determine the coordinates of the centroid of the trapezoidal area shown. Assumea = 200 mm, b= 340…

A:

Q: Angle: 34.9 Start point x: -9.7 y: -6.2 End point x: -3.1 y: -1.6

A:

Q: Is y = cx a solution of y' =2 ? Select one: O True O False What is the degree of 4 (* + sin x 3? +…

A:

Q: Explain what the differences between finite difference method and finite volume method.

A: Computational fluid dynamics (CFD) is a computer simulation tool for modelling fluid dynamics, that…

Q: 6

A: Step 1:Step 2: Step 3:

Q: Determine the vertical displacement of joint A. Each bar is made of steel and has a cross-sectional…

A: The cross-sectional area is 600 mm2.The modulus of elasticity is 200 GPa.Consider the figure.

Q: 100 Mpa 75 Mpa 150 Mpa If the element shown was rotated 60° CW Find: (α)σχ' (b)oy' (c)tx'y'

A: Asked: To compute the plane stress on the given element after rotation.   Given: Normal stress along…

Q: x=3, y=4, z=2. Please caclute if I am correct. Want to know if I am correct.

A:

Q: Use Virtual work method Find the following; (a) Rotation at C A (b) Horizontal displacement at C 12'…

A: Given: Determinate frame Virtual work method

Q: The following may be used in getting the resultant of forces except: A Square Rule B Triangle Rule…

A: Correct option is a) Square rule

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.