Analyze and determine all force members by hand calculations for the determinate structure. Once calculated, use the method of virtual work to calculate deflection at the point of maximum deflection (middle member)

Analyze and determine all force members by hand calculations for the determinate structure. Once calculated, use the method of virtual work to calculate deflection at the point of maximum deflection (middle member)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Idealize the following braced frame as a truss. Compute the horizontal deflection at Node A. ● ● ● E = 29000 ksi Column: A = 10.0 in.² Diagonal brace: A = 1.09 in.² Beams: A = 10.0 in.2 14 20k 1OK 77777 16' A
A cantilever of length I, and flexural rigidity El, stiffened by a spring of stiffness k, is loaded by a transverse force P, as shown. 1,EI mm The transverse deflection under the load is
Please give me complete right solutions. Urgenttttttt please
Both portions of the rod ABC are made of an aluminum for which E = 70 GPa. 0.4 m 0.5 m B P 20-mm diameter 60-mm diameter 2. What is the value of Q in kN so that the deflection at A is zero if P = 59 kN?
In the structures shown below all members have the same Young's Modulus, E, second moment of area, I, and cross sectional area, A. (a) Calculate the vertical deflection of the point load in the structure shown below. L A L (b) Using the principle of virtual work, calculate the internal forces in all the members in the structure shown below L A в (c) State all the assumptions. B
Use the method of virtual work and determine the vertical and horizontal displacement of joint F of the truss. Each steel member has a cross-section area of 300 mm2, E = 200 GPa. 60 kN E 2 m A B 2 m 2 m 2 m
In the restrained beam shown, solve for the following a. end moments b. max deflection note: use double integration method 3 kN /m 15KN 1m マク Im
A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal before the load Pis applied. Bars (1) and (2) are both made from steel [E = 29000 ksi] and both have a cross-sectional area of 1.15 in.?. Assume L1=73 in., L2=118 in., a=54 in., b=100 in., and c=48 in. If the normal stress in each steel bar must be limited to 15.3 ksi, determine the maximum load P that may be applied to the rigid bar. (2) (1) L2 A В C D a b V P
6. A 2-bar truss is as follows. AB= 4 m, BC=5 m, AC=3 m. The black block on C is a friction plate. When the friction coefficient is greater than u, the truss is stable. Determine the value of μ. A P B Hint: First, determine the internal force of AB and BC bar by Joint method at Joint B, Second determine Cx, Cy by Joint method at Joint C; then determine the value of µ.
Determine the horizontal deflection at joint C of the truss by virtual work method. Use E = 10,000 Ksi. A = 5 in² L1 = 4 ft, L2 = 5 ft, L3= 12 ft, P = 26 K, A L1 B __ L2 → P L3 K
Determine the deflection at joint B. Members have the same moment of inertia of 1440 x 10^4 cm^4 and E is constant at 210 GPa Using Unit load Method 100kN/m B P= 279 kN 100kN/m A 4m iP in kN 3m 5m
Please answer carefully, do not copy. It's all wrong online.