An RCC beam of 250 mm width and 400 mm effective depth is having three bars of 16 mm diameter of Fe415 grade in tension zone near a simply supported end. Factored shear force at the support is 250 kN. Factored moment of resistance is 50 kN-m. Grade of concrete is M20 with T = 1.5 MPa for plain bars is tension. Choose the correct statement(s) regarding this beam: A Development length requirement is 341.75 mm. Anchorage length beyond centre of support is 341.75 mm. Correct Option C Development length requirement is 601.75 mm. Correct Option Anchorage length beyond centre of support is 601.75 mm.

An RCC beam of 250 mm width and 400 mm effective depth is having three bars of 16 mm diameter of Fe415 grade in tension zone near a simply supported end. Factored shear force at the support is 250 kN. Factored moment of resistance is 50 kN-m. Grade of concrete is M20 with T = 1.5 MPa for plain bars is tension. Choose the correct statement(s) regarding this beam: A Development length requirement is 341.75 mm. Anchorage length beyond centre of support is 341.75 mm. Correct Option C Development length requirement is 601.75 mm. Correct Option Anchorage length beyond centre of support is 601.75 mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the design of beam for the limit state of collapse in flexure as per IS 456 : 2000, let the maximum strain in concrete be limited to 0.0030 (in place of 0.0035) for this situation consider a rectangular beam section of width 300 mm, effective depth as 400 mm, area of tension steel used is 900 mm2. Material used is M20 concrete mix Fe415 grade steel (a) Limiting depth of neutral axis (b) Actual depth of neutral axis
4. An interior reinforced concrete slab has to be designed to support a live load and a dead load in addition to its own weight based on the following specifications: The slab is one-way and simply supported with a span of 12 ft. The live load on the slab is 200 psf. The dead load on the slab is 100 psf. Your design will use concrete compressive strength fe= 3000 psi and steel yield strength of fy = 40,000 psi
Determine the additional longitudinal reinforcements (mm2) due to torsion of a rectangular beam with a width of 469 mm and an over-all depth of 632 mm. It is subjected to a factored torsion of 110 kN-m. The specified compressive strength of concrete is 21.70 MPa. The yield strength of tension reinforcements and stirrups are 348 MPa and 278 MPa respectively. Use 12 mm stirrups. Round off only on your final answer (3 decimal places).
Question Discuss the Plastic Hinge Length for this :- O simply supparted with concentrated Lead. simply supparted with uniform Load. O Simply supprted with two concentrated Load 4 Cantliver beam with cancentrated Lead at,end. Free Cantliver bea with distributed Load. you Can use wusw.concrete.org> SP_12 this salution to Find subject/Advanced Concrete Design Dear, flease help me to find solution far it question. un 部 odd case(4) Case Q) P case(3) Case (4) A case(5) distributed load (u)
7.b
Given the concrete (f c=6000 psi) I-beam shown in Figure 1 for the given loading: -draw the shear & moment diagrams -determine Vmax & Mmax -using ASD (Allowable Stress Design) method, check to see if the given loading produces stresses within the given allowable range (check both Omax & Vmax) Using ACI 318-99, allowable stresses are -for flexure, f = .45f'c -for shear, v. = 1.1√f. (HINTS: 8² -note that the beam is symmetric about both axes -Ix for a triangle is (1/36)bh³+Ad² ) 30 kips 16' 10 kip/ft 22' 20 kips 3'-4' -1-6 -1'-6" Figure 1 1'-
5. The beam shown is reinforced for positive moment with three epoxy-coated #11 bars. The bars terminate at the center of the supports. Neglecting beam weight (concentrated loads are very heavy), determine if the required development length is satisfied. Assume As required = 4.55in², 2 in. clear cover on all sides of the longitudinal reinforcement, normal weight concrete, #3 stirrups @12 in o.c., f'c = 5000 psi and fy = 60,000 psi. 8 ft | Pu 20 ft Pu 8 ft ge2 of 56 30 in b=14in. ed 5/15/2020 As = 3-#11
A beam has a width of 280 mm and 490 mm overall depth. Concrete cover is 65 mm from the centroid of bars. Concrete compressive fc' = 24 MPa. Steel yield strength are fy=415 MPa and fy = 275 MPa for ties. Determine the shear strength provided by concrete using simplified method a) If the beam is subjected to shear and flexure only, and b) If the beam is subjected to axial compressive force of 124kN.
A RC column is having 1% steel of cross sectional area of column. Assurme a modulus ratio of 10. The loads carried by longitudinal steel is Ps and that by net concrete area is Pc. Find the ratio Ps/Pc, in terms of percentage.
PLEASE SOLVE AND BOX ALL FINAL A LITTLE CONFUSED
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MPaa) depth of the compression blockb) strain in the tension reinforcementc) moment reduction factor