An RCC beam is of size 230 mm x 500 mm overall depth and effective cover to compression steel and tension steel are 50 mm. The compression reinforcement consists of 2 nos. 16 mm diameter bar and tension steel consists of 2 nos. 25 mm diameter bars. This doubly reinforced beam is made of M20 concrete and Fe415 steel. For Fe 415 0.05 0.10 0.15 0.20 f.(N/mm) 355 353 342 329 Which of the following is/are true? Actual depth of Neutral Axis (NA) is 131.1 mm. Correct Option This is an under reinforced section. Correct Option C The moment of resistance of this beam is 140.72 kNm. Correct Option The moment of resistance of this beam is 183.455 kNm.

An RCC beam is of size 230 mm x 500 mm overall depth and effective cover to compression steel and tension steel are 50 mm. The compression reinforcement consists of 2 nos. 16 mm diameter bar and tension steel consists of 2 nos. 25 mm diameter bars. This doubly reinforced beam is made of M20 concrete and Fe415 steel. For Fe 415 0.05 0.10 0.15 0.20 f.(N/mm) 355 353 342 329 Which of the following is/are true? Actual depth of Neutral Axis (NA) is 131.1 mm. Correct Option This is an under reinforced section. Correct Option C The moment of resistance of this beam is 140.72 kNm. Correct Option The moment of resistance of this beam is 183.455 kNm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a two span beam subject to shear and flexure only is reinforced as follows: Section: TOP BARS @ midspan: 2-ø20mm @ face of supports: 5-ø20mm Section: BOTTOM BARS @midspan: 3-ø20mm @ face of supports: 2-ø20mm GIVEN: Stirrup diameter ds = 10mm concrete f'c= 21 mpa steel rebar fy= 415 mpa stirrup fy = 275 mpa beam size b x h = 270 mm x 450 mm assume all bars laid out in a single layer. Determine the DESIGN moment strength of section at midspan for positive bending
Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including its own weight) and a live load moment of 300kN.m. The beam is limited in size to 350mm by 600mm overall depth. Steel covering from centroid of bars to outermost fiber is 100mm for both tension and compression reinforcement. Use fc'=27.5Mpa, fy = 414MPa,20mm barsA. As'= 7 of 20mm and As=14 of 20mmB. As' = 9 of 20mm and As=18 of 20mmC. As'= 5 of 20mm and As=10 of 20mmD. As' = 3 of 20mm and As=6 of 20mm Please provide neat and clear solutions Note: kindly check below answer
Do not use chatgpt and pls don't provide image solution otherwise I will downvote you
A 8 m simply supported singly reinforced beam has a width of B= 39 cm and a height H=61 cm. Concrete compressive strength, f'c-30 MPa Steel Yield Strength of longitudinal bars, fyl-420 MPa, Steel Yield Strength of transverse bars, fyt -280 MPa, Unit weight of concrete, 24.4 kN/m³. Steel cover of the beam = 6 cm It is desired that the capacity of the beam to be at balanced condition. If the structural engineer wants the optimization ratio of the design moment and capacity to be 0.66, calculate the maximum value of the live load in kN/m to meet such condition Use NSCP2015
I need the answer to the question in reinforced concrete
a simply supported beam 300mm wide, 500mm deep and spans 5.7m supports a service super imposed dead load of 8kN/m and service live load of 7kN/m. concrete strength f'c=21MPa and steel yield strength fy=415MPa. concrete cover to bar centroid is 70mm. determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015.
30" Design the reinforcement for the T-beam in the middle which carries a live load of 200 lb/ft². The length of the beam is 25 ft. In your design assume concrete with a compressive strength of 3,000 psi density 150 lb/ft³ and Grade 60 Steel. 27" 12" 10'-0" 12" 10'-0" 12"
Combined Stresses Given Hollow Steel Section (HSS) that is 4"x6" and 1/2" thick, with axial and transverse loading shown, determine the total normal stress at a. The 5k load on the bottom of the beam b. At the mid-span in the middle of the beam C. At the 10k load on top of the beam 5k 10k A 5' 10' 5' B CENTROID 4" 5 k 3k 8k 6" 2' 6.25k 8.75k +6.25k SECTION +1.25k 'V" -8.75k +43.75k-ft. +31.25k-ft. 'M' 8k 5 k + tension P = Ok %3D
5. The beam shown is reinforced for positive moment with three epoxy-coated #11 bars. The bars terminate at the center of the supports. Neglecting beam weight (concentrated loads are very heavy), determine if the required development length is satisfied. Assume As required = 4.55in², 2 in. clear cover on all sides of the longitudinal reinforcement, normal weight concrete, #3 stirrups @12 in o.c., f'c = 5000 psi and fy = 60,000 psi. 8 ft | Pu 20 ft Pu 8 ft ge2 of 56 30 in b=14in. ed 5/15/2020 As = 3-#11
For the following plan it is required to: 1- Design all beams for flexure and shear, where they have additional 30 kN/m distributed factored load 2- Design the columns. The concrete has a strength of 30 MPa, and the yield strength of the steel is 420 MPa. Show full calculations and neat sketches. All dimensions are in m. I 03 B2 0,3 7 B1 Wu=20 kN/m2 B1
3-2 A rectangular section with width b=200mm and depth h=450mm is to carry a design bending moment M=145KN •m. The concrete is of grade C40 and the tensile steel is of HRB400. The tension reinforcement A, is required.
1. A two span beam subjected to shear and flexure only is reinforced as follows: SECTION: TOP BARS @ MIDSPAN: 2-⌀20mm @ FACE OF SUPPORTS: 5-⌀20mm SECTION: BOTTOM BARS @ MIDSPAN: 3-⌀20 mm @ FACE IF SUPPORTS: 2-⌀20 mm Given: Stirrup diameter, ds = 10 mm Concrete f'c = 21 MPa Steel rebar fy = 415 MPa Stirrup fy = 275 MPa Beam size b x h = 270 mm x 450 mm Assume all bars laid out in single layer. Calculate the following: a. Design Moment strength of section at midspan for positive bending = ______ kN·m (nearest whole number)