An owner's concern indicates excessive play in the steering wheel: Technician A checks the steering shaft U-joints. Technician B performs a dry park check of the linkage. Who is correct?   a. Technician A     b. Technician B     c. Both A and B     d. Neither A nor B

Q: While diagnosing the problems that can be caused by worn tie-rod ends: Technician A says that they…

A: Tie rod ends: The tie rod is a part of the steering system. The tie rods joins the spindle, on which…

Q: What is the purpose of of the viscous clutch?a. to engage engine otrque to the transmission.b. to…

A: The correct option is: b. to improve mobility when driving conditions become difficult Explanation:…

Q: The main job of the idler arm is to __.a. support the left side of the center linkb. support the…

A: The idler arm is designed to keep the center link parallel to the road surface while allowing the…

Q: In a rack and pinion steering system, what protects the rack from contamination? a. The inner…

A: A gear set converts the circular motion of the steering wheel into the linear motion necessary to…

Q: Technician A says that some small cracks in the accessory drive belt may be within tolerance.…

A: Technician A says that some small crack in the accessory drive belt may be within tolerance limits.…

Q: Before servicing a hydraulic power booster system, ______. a. drain the power steering reservoir b.…

A: Solution: Before servicing a hydraulic power booster the following steps are followed, Step1: First…

Q: When discussing the possible causes for a shudder during acceleration, Technician A says that a worn…

A: Shudder is taken place during acceleration at higher speed. The main reason of this problem is…

Q: Tech A says that camber changes as the suspension moves up and down.  Tech B says that camber…

A: Camber angle : The angle made by the vertical axis with the wheel is known as camber angle . It is…

Q: Technician A says that a malfunction of the ABS causes the control module to shut off or inhibit the…

A: The system will be shut down if any malfunction is monitored in the ABS because the control module…

Q: Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the…

A: A drum brake is a brake that uses friction caused by a set of shoes or pads that press outward…

Q: 6. While discussing types of coil springs: Techni- cian A says that linear-rate coil springs have…

A: Q.6) Answer" Both Technician A and B is correct. Technician A is correct because in Linear rated…

Q: What results from having different axle ratios on thefront and rear of a 4WD vehicle when it is…

A: Given Data : 4WD Axle ratio

Q: vehicle is producing a sharp, metallic rappingsound originating in the upper portion of the…

A: As per suggestion of Technician A: If the vehicle is producing sharp, metallic rapping sound from…

Q: When examining disc brakes: Technician A visually inspects the rotor and says that the rotor can be…

A: Technician A is correct.

Q: Explain the primary operational difference between a full time and a part time four wheel drive…

A: Introduction A four-wheel drive vehicle, often known as a 4WD or four-by-four, is one that receives…

Q: The CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the…

A: The function of engine mounts is to limit the movement of the engine, hold it in a position and…

Q: 2. Technician A says that the purpose of the steering wheel holder is to make sure that the steering…

A: In this problem, Technician A is talking about the purpose of a steering wheel holder. He is telling…

Q: What can too much clutch pedal free play cause? a.hard gear shifting b.fast release bearing wear…

A: The correct option is d. clutch slipping. Excessive clutch pedal free play can cause the clutch to…

Q: Technician A says that some shift solenoids can be activated by providing a ground for the solenoid.…

A: The shift solenoid is used in the gear assembly which shifts the gear according to the desire of…

Q: Pinion gear-to-flywheel ring gear clearance is beingdiscussed: Technician A says that if there is…

A: Given  Pinion gear-to-flywheel ring gear To find Which technician is correct

Q: The part (most likely to fail) in a parallelogram-type steering system is the ______.   a. idler…

A:

Q: Technician A says that the piston seal retracts the caliper piston when hydraulic pressure is…

A: Technician A is correct.

Q: The functions of a splash shield are being discussed: Technician A says that disc brakes will…

A: The splash shield is a metallic or plastic part that is placed at the bottom portion of the car. The…

Q: What is the correct sequence for adjusting alignmentangles during a four-wheel alignment?

A: Given Data : Adjusting alignment angles during four wheel alignment.

Q: The steering wheel angle is 80° and the steering ratio is 14. Calculate the slip angle of each wheel…

A: Steering angle = 80oSteering ratio = 14The objective is to calculate the slip angle of each wheel in…

Q: When discussing axle hub nuts, Technician A says that they are never to be reused after they have…

A: Solution:

Q: When discussing CV joint diagnosis, Technician A says that the complete failure of a CV joint may…

A: Solution:

Q: Technician A says that broken or worn engine and transaxle mounts can cause a transaxie to have…

A: Given Transaxle problem To find Statement with is/are correct Shifting problem of transaxle can be…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.