In a rack and pinion steering system, what protects the rack from contamination? a. The inner tie-rod socket b. The outer tie-rod socket c. Grommets d. The bellows boot

Q: While diagnosing a complaint of excessive play in the steering on a vehicle with power steering:…

A: The correct option is b.

Q: What is the purpose of of the viscous clutch?a. to engage engine otrque to the transmission.b. to…

A: The correct option is: b. to improve mobility when driving conditions become difficult Explanation:…

Q: The main job of the idler arm is to __.a. support the left side of the center linkb. support the…

A: The idler arm is designed to keep the center link parallel to the road surface while allowing the…

Q: Which of the following statements about unibodyconstruction is not true?a. A unibody is a stressed…

A: When a car's structure and body are produced as one piece, it is known as unibody construction.…

Q: Before servicing a hydraulic power booster system, ______. a. drain the power steering reservoir b.…

A: Solution: Before servicing a hydraulic power booster the following steps are followed, Step1: First…

Q: When discussing the possible causes for a shudder during acceleration, Technician A says that a worn…

A: Shudder is taken place during acceleration at higher speed. The main reason of this problem is…

Q: What type of axle merely supports the vehicle load and provides a mounting place for the wheels?

A: Axles are very important parts of an automobile. These axels are used to supports the loads and…

Q: Technician A says that a malfunction of the ABS causes the control module to shut off or inhibit the…

A: The system will be shut down if any malfunction is monitored in the ABS because the control module…

Q: )Explain how to move the vehicle in reverse at variable speeds with the engine at

A: As the engine cannot rotate in reverse direction as shaft rotate in reverse direction  and car will…

Q: Which of the following components is replaced as an assembly?a. The transfer caseb. the viscous…

A: Step 1:The transfer case is often replaced as an assembly due to several reasons :Transfer cases are…

Q: What results from having different axle ratios on thefront and rear of a 4WD vehicle when it is…

A: Given Data : 4WD Axle ratio

Q: Q4: Look and match 28 26 1.4 24 22 27 25 30 29 24 23

A: In an aircraft, most flight-controlling instruments are set near the cockpit.

Q: What is the safest way to drive a forklift in reverse? Keep your eye on the load, but turn around…

A: 11. Steel jacks are mainly needed to provide support to the trailer jack. When the trailer is…

Q: Explain the primary operational difference between a full time and a part time four wheel drive…

A: Introduction A four-wheel drive vehicle, often known as a 4WD or four-by-four, is one that receives…

Q: When discussing shift problems, Technician A says that worn or broken engine and transaxle mounts…

A: A chain of gears which is used to pass on the power to the wheel from the engine is called as…

Q: Which of the following statements is NOT true about limiting position (s) of a mechanism? A. A…

A:

Q: Section angle of V-belt in belt drive φ=40˚,In order to make good contact and increase friction, the…

A: To find: The pulley groove angle. Given: The section angle of V-belt drive is φ=40°. Explanation:…

Q: 2. Technician A says that the purpose of the steering wheel holder is to make sure that the steering…

A: In this problem, Technician A is talking about the purpose of a steering wheel holder. He is telling…

Q: The part (most likely to fail) in a parallelogram-type steering system is the ______.   a. idler…

A:

Q: Design and model of a basic mobile platform (2 wheel drive)

A:

Q: tart capacI 11. A cylindrical sleeve bearing, typically made of bronze, is called a A. bushing B.…

A: To find :- Correct option

Q: A power-steering hose transmits fluid under pressure from the ___ to the ___ ___ ___ ?

A: Consider the diagram shown below for the power steering system, Power steering is used to assist…

Q: The causes of suspended load in the traction system are: a. Laminar current b. turbulent current c.…

A: The cause of suspended load in the traction system are turbulent current.

Q: The steering wheel angle is 80° and the steering ratio is 14. Calculate the slip angle of each wheel…

A: Steering angle = 80oSteering ratio = 14The objective is to calculate the slip angle of each wheel in…

Q: When discussing CV joint diagnosis, Technician A says that the complete failure of a CV joint may…

A: Solution:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.