An orifice having an area of 0.0075 m2 is attached to a vertical side of a cylindrical tank (Diam= 4m.). The weight of the water discharged in 87 sec. is 20,598 N. under a constant head of 1.36 m. The jet strikes a point 1.55 m. horizontally from the vena contracta and 0.6 m. vertically below the orifice. Compute the coefficient of contraction, Cc.

Q: An orifice at the bottom of a rectangular tank has a cross-sectional area of 0.004m². The tank has a…

A: We have to find coefficient of discharge and time to lower the water surface from 5.6m to 3m.

Q: 3. A prismatic vessel has two compartments A and B communicating by an orifice 0.25 m square with C…

A:

Q: 4. A prismatic vessel has two compartments A and B connected by a 30cm x 30cm standard orifice. The…

A: Orifice:An orifice is a small entrance on the side or bottom of a tank that enables any type of…

Q: Determine the pressure at the higher end if the pressure at the lower end is 24.525 N/cm^2. 23.924…

A:

Q: A right circular tank 6 m. in diameter and 12 m. high is filled with 6 m. of oil sp. gr. = 0.80 and…

A: Diameter of tank = 6 m Initial Height of fluid = 12 m Diameter of orifice = 75 mm

Q: Determine the force acting on hydraulic cylinders ED and AC if the excavator applies a 20 kN force…

A: Given -

Q: Piston A has a cross sectional area of 1400 mm2 While that of piston B is 1000 mm2. B is higher than…

A: Pb=F/Area of piston b=4/0.001=4000 kN/m2 taking  ρ= 800 kN/m3    g=9.81 m/s2…

Q: A rectangular tank 3.6 m long and 1.8 m wide is divided into two parts, by a vertical dividing plate…

A: Volume of water required to be removed= 3.6*1.8*0.9*0.66= 3.84912 m3. Area of cross section of…

Q: Pressurised water flows through two connected circular pipes as shown in Figure 1. Location 1 is at…

A: Given: Discharge  Diameter  Elevation difference  To find: Headloss between two sections Note : Z1 =…

Q: Water flows through an orifice at the vertical side of a closed cylindrical tank. The water level…

A:

Q: 6.88m. Darcy-Weisbach friction factor for all pipes, f=0.0238.    Pipe 1: Length=3500m…

A:

Q: A pipe (AB) that is 2300 m long and 400 mm diameter ,carries 150 L/s, C%=D100 ,the elevation of…

A:

Q: Water flows at a rate of 0.1 m³/s through the horizontal pipe transition as shown below. Pressures…

A: Q = 0.1 m3/s D1 = 0.1 m D2 = 0.2 m P1 = 19620 PaP2 = 49050 Pa

Q: A 75 mm diameter orifice discharges 0.023 m/s of liquid under a head of 2.90 m. The diameter of the…

A:

Q: Question 4. The flowrate of the flow is 0,2c m³/s in a pipe placed on a horizontal plane. The pipe…

A: Given Q= 0.2 m3/s D1=0.4m D2=0.8m P1=80 kN/m2   Fx=force component in x direction Fy=force component…

Q: The large tanks A and B are connected by a variable section pipe. The water level in tank A is 2m,…

A:

Q: pipeline connected to a reservoir discharges water 30 m below the free surface in  the tank. The…

A:

Q: If the inlet diameter of the holding tank is 35cm and the outlet diameter is 30cm and the diameter…

A:

Q: Question 2. la0 mm diameter siphon draws water from the reservoir. Considering that the elevation…

A: Discharge is the main quantity in any field used to transfer fluids from one place to another. It…

Q: Water flows through an orifice at the vertical side of a closed cylindrical tank. The water level…

A:

Q: SITUATION. A closed cylindrical tank with 0.60 m diameter and 1.0 m height is fully-filled with…

A:

Q: Problem 1. A 75-mm diameter orifice discharges 0.023 m3/s of liquid under a head of 2.90 m. The…

A: Given data,  Diameter of orifice = 75 mm Discharge = 0.023 m³/s Head = 2.9 m Diameter at vena…

Q: 2. A closed vertical cylindrical vessel, 1.50m in diameter, 3m high is 8/10 full of liquid (SG=1.03)…

A:

Q: A 300 mm diameter cast-iron pipe of 1000 m length delivers water from an upper reservoir to a lower…

A:

Q: Water flows with a flow rate of 0.6 cumec through an inclined pipe PQ of length 10 m lengt having a…

A: Flow rate = 0.6 cumecLength of pipe PQ = 10 mAngle = 30 degreePressure = 30 kN/m2We have to…

Q: 5. A right circular tank 6 m in diameter and 12 high is filled with 6 m of oil sg = 0.88 and 6 m of…

A: Diameter of tank = 6 m Initial Height of fluid = 12 m Diameter of orifice = 75 mm

Q: Provide complete solution.  A frustum of a cone is shown, with the orifice at the bottom. C_d=0.62.…

A:

Q: A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev.…

A:

Q: he hole by a distance x. Given: h = 0.85 m, a = 0.4 m, b = 0.7 m. Determine: by what distance x do…

A: Given:- h = 0.85 m, a = 0.4 m, b = 0.7 m.  To find:- by what distance x do we have to move the…

Q: Q1: For the set up shown in the following figure. Determine the total head, pressure head, elevation…

A: As head at E is more than head at B flow is in upward direction. n = Porosity = 0.34K = Permeability…

Q: The water tank has a rectangular crack on its side having a width of 100 mm and an average opening…

A: width of crack (wc) = 100 mmopening of crack (Lc) = 0.1 mmT=20o CLength of crack (L) = 200 mmh=2 m

Q: Water 6 m F₂ Figure la F₁ 2 m Gate m

A:

Q: 1. A circular orifice 30 mm in diameter, in the interval side of a vessel, discharge water under a…

A:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?