An open cylindrical tank 2m in diameter and 4m high contains water to a depth of 3m. It is rotated about its own vertical axis with a constant angular speed w. If w = 4 radsec, what is the volume of liquid spilled?

Q: Problem 2 The containers A and B, shown on the figure, are filled HO with water, with density Pwater…

A:

Q: A 1.5m cylinder (s=2.45) is 10m long and it held two different liquid at both sides. If the liquid…

A: Given data  Specific gravity  Length  Depth Radius   I have assumed the depth of left side fluid is…

Q: ÞA P9 UA 2g =? = 7m DA=0.2m ZA=10m Akım borusu DB=0.3m 24B 2g =? Þs pg =? ZB=15m ds (v. dQ. dt) =…

A:

Q: rsion, the liquid was 8 cm dee

A:

Q: Two pipes of diameters d1 and d2 converge to form a pipe of diameter d. If the liquid flows with a…

A:

Q: D A cylindrical tank with its axis vertical gas a diameter of 2 m and a depth of 8 m. A standard…

A:

Q: 7. At some instant in time, Piston A is moving to the right at a velocity of 0.500 m/s and Piston B…

A:

Q: The actual velocity in the contracted section of a jet of liquid issuing from a 5 cm diameter…

A: 1. Diameter of the orifice = 5 cm2. Actual velocity in the contracted section = 7.5 m/s3. Head…

Q: A rectangular tank 3 m long, 1.40 m wide and 1.80 meter high contains oil with specific gravity of…

A:

Q: A 50 mm diameter siphon draws oil (S.G. = 0.82) from a reservoir. If the head loss from point 1 to…

A:

Q: The large tank shown in the figure contains water and shoots it up using a pump connected to its…

A: In the given figure a pump placed at the bottom of the tank of depth 20 m raised the liquid to 27 m…

Q: An open horizontal tank 3 m high, 3.5 m wide and 6 m long is initially filled at 2 m of water. a.…

A: Hydrostatic force Hydrostatic forces are the resultant forces caused by the pressure loading of a…

Q: The pressure in the outlet pipe from the reservoir is 61.3 kPa abs and h =15 m. Because of the…

A:

Q: A sharp-edged circular nozzle with a cross-sectional area of 10 cm2. Water flows from it under the…

A: Actual velocity calculation:…

Q: 17. An open cylindrical tank 4 m in diameter and 10 m high contains 4 m of oil sg = 0.9. An orifice…

A: The objective of the question is to calculate the time required to discharge all the oil from a…

Q: 1. A cylindrical tank, 1.5m inside diameter has an orifice at its side 0.25m above the bottom. If…

A: Reference : Water resources, Orifices.Given :Diameter of orifice, height of water.To determine :1.…

Q: 17. An open cylindrical tank 4 m in diameter and 10 m high contains 4 m of oil sg = 0.9. An orifice…

A:

Q: An inverted cone has a radius of 12ft and height of 15ft. The cone is 80% full of a fluid having a…

A: AT 80% THE HEIGHT =0.8h=0.815=12ftso radius ish80%r80%=hrr80%=0.8×hh×12r80%=9.6ftFind volume of…

Q: Water flows through a pipe before passing through a nozzle and exiting as a free jet to the…

A: In this question we use a) coefficient of contraction formula Cc = (Area of jet at vena contracta /…

Q: 3. An open cylindrical vessel, 800mm in diameter, 1.2 meters high, and 3/4 filled with water rotates…

A: Given Data Diameter of cylinder (d) = 800 mm = 0.8 m  Hight of cylinder (H) = 1.2 m  Depth of water…

Q: A cylindrical vessel with closed bottom and open top is 0.9 m in diameter. What is the rotational…

A: Given- Dia of open top=0.9 mrise=0.5 mbottom dia=0.4 mg=10 m/s2 Rotational speed needs to be find…

Q: The ball B of negligible size rolls through the tube such that at the instant shown in (Figure 1) it…

A: Given: To find: Part A: Velocity of the ball if the tube has an angular velocity, ω = 3 rads/s and…

Q: A 5-m container having the dimensions 1.2x1.2 m² has a sharp-edge orifice 100mm located at its side…

A: Dimensions of the container =Diameter of the orifice = =0.1 mArea of the orifice =AThe depth of…

Q: III of dia. 1.0 m is connected to a pipe of 0.1 m in dia. as can be he fluid height inside the tank…

A:

Q: 5. A right circular tank 6 m in diameter and 12 high is filled with 6 m of oil sg = 0.88 and 6 m of…

A: Diameter of tank = 6 m Initial Height of fluid = 12 m Diameter of orifice = 75 mm

Q: Question- A pelton wheel works under a head of 400m. Friction loss through the pipe flow is limited…

A: Given- Pelton wheel- Head h=400 m, friction loss=10%, Coefficient of velocity Cv=0.98, g=10 m/s2, It…

Q: Problem No. 1 An open rectangular tank 3. 8m high, 2. 5m wide and 6m long is filled with water at a…

A: Given data in question  Dimensions of vessel Angle of slope Acceleration  To find out  Acceleration…

Thermal Processes

Some of the key areas where thermal processes find their application are: