A vertical cylinder having a circular base of radius 'r' and a height of 12 m is filled with water at the rate of 1 m/min. If the depth of water in the cylinder at the vertical position is 3 m, what would be the resulting depth when the cylinder is in the horizontal position? OA 0.30r O B. 0.40r OC.0. 50r O D.0.60r

A vertical cylinder having a circular base of radius 'r' and a height of 12 m is filled with water at the rate of 1 m/min. If the depth of water in the cylinder at the vertical position is 3 m, what would be the resulting depth when the cylinder is in the horizontal position? OA 0.30r O B. 0.40r OC.0. 50r O D.0.60r

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A circular tank has an 34mm diameter orifice on one of its sides discharging oil with a specific gravity of 0.89. The tank has a 553mm diameter and has a depth of 2.7m. The orifice is located 0.20m above the bottom of the tank. The depth of oil inside the tank was initially 2.3m and 264s later, it became 0.7m. What is the coefficient of discharge?
I need the answer to the question in fluid mechanics
i need the answer quickly
*hydraulics *use handwritten A trapezoidal flume of most efficient proportion has a base of 1.5 m. Its full discharge is 3 m^3/s, If the same material is used for a most efficient rectangular section, Compute the decrease in the discharge. Choices: A. 0.44 m3/s B. 0:54 m3/s C. 0.64 m3/s D. 0.74 m3/s
Example 8: A flocculation basin is designed to treat water of 1 m³/s flow rate. The length of the basin is 30 m and width is 12.25 m and the basin depth is 4.5 m. The basin is provided by four axes (shafts) a long its length, each shafts has two blades, the width of each blade is 0.3 m with 12 m length, the distance between the center of shaft and the center of each blade is 2 m, the coefficient of drag is 1.8, the velocity of blade in the basin 2.5 rpm. use (u = 1.312 * 10-3) N.s/m², p= 1000 Kg/m³. calculate: 1- The power requirement in unit of (KW). 2- Flocculation time in unit of (min). 3- The volume of G of each blade.
Thanks !!!!
ANSWER ASAP. WILL UPVOTE
Question:- A. Determine the distribution of flow rate in the network tubes. B. Obtain the pressure in node D.
3. A horizontal pipe 1.0 m in diameter and 2.50 km long takes off from a reservoir 100 meters below the reservoir water surface and extends to a valve that is to be closed in 25 seconds. During closure, the flow velocity is reduced from 8 m/s to 0 m/s. Express the required thickness of the pipe in term of X. X is the distance of any section/point along the pipe from the reservoir. Use 1.24 X 105 KPa as the working stress of steel. Assume Up = 950 m/s. valve Any point
???
answer is given just give the solution and right answer.
The water flow of 35,000 Liters/min was developed into a booster station with a pump installed rated as follows: Pressure at Discharge side= 4.18 bars, 850mm above the pump C.L Suction Pressure= 220mmHg vacuum , 425mm below the pump C.L Pipe Dia @ suction=16 inches and Pipe Dia @ Discharge 12 ½ inches. 1. Draw the illustrative diagram 2. Calculate the Head at discharge, Velocity Head, Elevation Head and the Total Head of the Pump.