An oil pump operating at steady state delivers oil at a rate of 10 lb/s through a 1-in.-diameter ex as incompressible, has a density of 70 lb/ft³ and experiences a pressure rise from inlet to exit of elevation difference between inlet and exit, and the inlet kinetic energy is negligible. Heat trans surroundings is negligible, and there is no significant change in temperature as the oil passes thr Determine the velocity of the oil at the exit of the pump, in ft/s, and the power required for the p Step 1

An oil pump operating at steady state delivers oil at a rate of 10 lb/s through a 1-in.-diameter ex as incompressible, has a density of 70 lb/ft³ and experiences a pressure rise from inlet to exit of elevation difference between inlet and exit, and the inlet kinetic energy is negligible. Heat trans surroundings is negligible, and there is no significant change in temperature as the oil passes thr Determine the velocity of the oil at the exit of the pump, in ft/s, and the power required for the p Step 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3. An internal combustion engine consumes 6 kg of fuel per hour, ip of engine is 27 kW and mechanical efficiency is 80%. It uses 12 kg of cooling water per minute and the inlet and outlet temperature of water being 18 °C and 48 °C respectively. The exhaust gases raise the temperature of 8.4 kg/ water through 32 °C. The orific value of fuel used is 44 MJ/kg. Calculate the indicated thermal efficiency, overall efficiency of the engine and draw heat balance sheet.
Water flow through a pipe at 18 li/sec. The inlet diameter of pipe is 15 cm and its exit diameter is 10 cm. If water is to be pumped from water source 8.2 m and heat loses is 2.1 kw, determine the power input to the pump.
explain how to solve thanks
A centrifugal pump uses a 134767 rpm motor to pump 116334 kg/min of standard temperature water and has a pressure rise from 2 bar to 38 bar using a 0.11 cm diameter impeller. The Inlet diameter is 0.39 cm and the outlet diameter is 0.18 cm. The inlet and outlet are at the same level with each other. What will be your water power (in kW)? ?
In unloading a grain from a hold of a ship, an elevator lifts the grain through a distance of 12 m. Grain is discharged at the top of the elevator at a rate of 2.0 kg each second, and the discharged speed of each grain particle is 3 m/s Find the minimum-horsepower motor that can elevate the grain in this way if it is 60% efficient.
A pump delivers 4 ?3/??? of water from 110 kPa to 350 kPa. Both pipes’ gages are on the same level. The inlet and the outlet pipe diameters are 16 cm and 13 cm respectively. The inlet and outlet temperature are both 25 deg C and the mass density of water is 997 ??/?3. Calculate the pump work in kW. Please answer it with a complete solution thank you.
b and c please
3. A hydraulic lift is shown below. The combined mass of the piston, rack, and car is 4000 lbm. The working fluid is water. There is no heat transfer to or from the water, and the internal energy of the water per unit mass is constant. The water may be considered incompressible. (a) Taking all the water in the reservoir, line, and hydraulic cylinder as the system (i.e., taking the closed-system approach), calculate the work necessary to raise the rack and car 1 ft (neglect the change in potential energy of the water in the system). (b) Repeat part (a), taking all the water plus the car and the rack as the system. (c) Repeat part (a), taking an open-system approach; choose as your system the volume of the hydraulic cylinder, excluding the piston, rack, and car. If the absolute pressure in the system is 1000 lbf/in², calculate the volume that must flow in to raise the car 1 ft. Reservoir Pump Hydraulic cylinder
200Kg/min superheated steam at 40 bar and 350C enters a turbine through a 7.5cm ID pipe. It exits at 5bar as saturated steam through a 5cm ID pipe neglect the change in potential energy of the system. What is the temperature of the outlet saturated system? How much energy is transferred to or from the turbine?
A four-stage compressor works between limits of 1 bar and 120 bar. The indexof compression in each stage is 1.25, the temperature at the start ofcompression in each stage is 30 ˚C, and the intermediate pressure areselected such that work is divided equally among the stages. If the clearanceis negligible: Calculate:1 the intermediate pressure in each stage2 the temperatures at the end of each stage3 the mass flow rate in kg/h if work input is a unit kW
Q1 / A: Derive the steaay flow energy equation and reduce it for: a. A turbine ( Reversible Process) b. A pump ( Reversible Process) c. A nozzle ( Reversible Process) d. A throttling ( Irreversible Process) Assume that the working fluid is an ideal gas and the entrance and exit are at the same level. B- For a reversible adiabatic process prove the equation pvr = constant can apply for the relation between pressure and specific volume for a perfect gas. %3D
1. A pump is used to lift 11 CMH of water at 20°C from a nearby fresh water lake whose free surface is 2.5 meters below the pump centerline to an elevated water dam whose free surface is 10 meters above the pump centerline. The suction pipe and discharge pipe are DN 8 SCH 40 and DN 10 SCH 40, respectively. The suction pipe has a total length of 5.4 m, while the discharge pipe has a total length of 21 m. Assume Hazen-Williams coefficient of 140 for both suction and discharge pipes and ignore minor head losses. a. Draw a schematic of the problem. Clearly indicate the elevations with respect to the pump centerline. b. Calculate the total dynamic head of the pump in meters. c. Calculate the water power output of the pump in kW. d. Calculate the brake power input to the pump in kW, assuming a pump mechanical efficiency of 75%. e. Calculate the electrical power input to the pump in kW, assuming a motor efficiency of 90%.