An L = 37-ft-long soldier beam is used as a key component of an earth retention system at an excavation site. The soldier beam is subjected to a soil loading that is linearly distributed from WA = 600 lb/ft to wc=220lb/ft, as shown. The soldier beam can be idealized as a cantilever with a fixed support at A. Added support is supplied by a tieback anchor at B, which exerts a force of P = 5800 lb on the soldier beam at a = 28 ft. Determine the horizontal deflection of the soldier beam at point. C. Assume El = 4.0 x 108 lb-in.². Deflection is positive to the left. a P Tieback anchor WA WC C B Soldier beam L

An L = 37-ft-long soldier beam is used as a key component of an earth retention system at an excavation site. The soldier beam is subjected to a soil loading that is linearly distributed from WA = 600 lb/ft to wc=220lb/ft, as shown. The soldier beam can be idealized as a cantilever with a fixed support at A. Added support is supplied by a tieback anchor at B, which exerts a force of P = 5800 lb on the soldier beam at a = 28 ft. Determine the horizontal deflection of the soldier beam at point. C. Assume El = 4.0 x 108 lb-in.². Deflection is positive to the left. a P Tieback anchor WA WC C B Soldier beam L

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. Solve the following problem Determine the maximum torque T that can be resisted by two shafts with a circular section of outer diameter of 100 mm. For the first shaft, the section is solid (no holes). For the second shaft, the section is hollow with an inner diameter of 75 mm. Use an allowable shear stress Tallow = 100 MPa and provide a drawing of the shear stress distribution on both sections. Rug'd max T for solid shaft Tallow = 100MP₂ diameter d loomm T hole diameter dinner = 75mm max T for hollow shaft 2D stress distribution
A beam simply supported on a 8 m span carries a uniformly distributed load of 30 kN/m over the middle 5 m. Using an allowable stress. fb = 120 MPa. A. Determine the most economical W shape beam, with the condition that the depth of the beam shoul not exceed 500 mm. B. What is the actual stress in the selected beam?
c. If a hole of diameter d/2 is drilled longitudinally through the bar, what is the ratio of the torsional stiffnesses of the hollow and solid bars? What is the ratio of their maximum shear stresses if both are acted on by the same torque? d. If the hole diameter remains at d/2, what new outside diameter d2 will result in equal stiffnesses of the hollow and solid bars? Need help with these questions in regards to the same problem
From figure, given E=200 GPa, r=37.5mm, A= 2285mm^2 and I = 3.33 x 10^-6 m^4.Calculate the allowable centric load for the column and the corresponding stress using Euler’s formula by considering the factor of safety is 2.0
From the given figure below and its properties, calculate the stress at the top where at the fixed end. (MPa) Properties: Beam width = 274 mmBeam height = 419 mmWLL = 8.86 kN/mWDL = 12.6 kN/mPu = 7 kNSpan of the beam = 8 mPrestressing force = 399 kNeccentricity = 127 mm
Solve using method of consistent deformation; EI =4x10^6 KN m^2, L=3.0, Wo=20KN/m
H.W.2. : For the base shown in figure below, estimate the elastic settlement at point (A). The base is subjected to concentric total load of 7500 kN. Assume that the base is located at 3 m below the surface of a homogenous soil which has: E, = 15 MPa, µu = 0.3 and y = 15 kN/m 4 m 2 m2 m 2 m 2 m 6 m
Determine the following: a. Maximum and minimum principal stresses b. Normal and shear stresses on plane AB
Current Attempt in Progress Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 3150 mm2 and an allowable normal stress of 175 MPa. Bar (2) has a cross-sectional area of A2 = 2900 mm2 and an allowable normal stress of 140 MPa. Assume x1 = 1.9 m, x2 = 2.9 m, y1 = 1.4 m, and y2 = 2.4 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable %3D %3D normal stress. y2 A (1) В W P Answer: Pmax kN
Current Attempt in Progress Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 4650 mm² and an allowable normal stress of 80 MPa. Bar (2) has a cross-sectional area of A2 = 2800 mm2 and an allowable normal stress of 160 MPa. Assume x₁ = 1.5 m, x₂ = 3.1 m, y₁ = 1.5 m, and y2 = 2.5 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. A Answer: Pmax= (1) i B (2) C kN 1/₂
Hand written please
Find the expressions to calculate the maximum normal and shear stresses for a circular profile: d (diameter)= 0.30 m