An irrigation canal has a rectangular cross section. At one point where the canal is 19.8 m wide and the water is 3.5 m deep, the water flows at 2.61 cm/s. At a second point downstream, but on the same level, the canal is 16.35 m wide, but the water flows at 10.51 cm/s. How deep is the water at this point? Express answers in meters (m).

Q: A canal lock is 6m wide by 24m long. The time to empty the lock is 5 minutes. Determine the area of…

A:

Q: A channel of width 450 mm branches into two sub-channels having width 300 mm and 200 mm as shown in…

A: D=0.45m Q=0.9m3/s D1=0.3m D2=0.2m V2=3m/s V1=?

Q: What are the most economical dimensions for a rectangular brick channel designed to carry 10 m3/s of…

A: (1)Given data - Q = 10 cms n = 0.015 S = 0.001 Find out - What are the most economical dimensions…

Q: 9.168. Calculate the flowrates in the pipes of this network. The length, diameter, and f value is…

A:

Q: Calculate the values of critical height and critical velocity for water flowing through a…

A: Given: Width of channel, b = 7.5 m Flow rate, Q = 22.5 m3/sec

Q: A trough of water is 8 meters in length and its ends are in the shape of isosceles triangles whose…

A:

Q: P5: If water flows from the upper to the lower reservoir as shown in figure at a rate of 0.028m³/s…

A:

Q: You are working for a big engineering company. The company has a project on building a channel, and…

A: B = 20 m Q = Area x V

Q: When 3000L/min of water flows through a circular section with an inside diameter of 400mm cart…

A:

Q: 5.1 You are tasked with designing a pipeline that supplies water to two parallel mansions at Stein…

A: To determine the flow in each branch of the pipeline, Flow rate in branch = total flow rate * (1 -…

Q: A rectangular canal is designed to carry 8.5 cu.m./s at a velocity of 2.1 m/s. For a most efficient…

A:

Q: Find the flow in pipes 1, 2, 3, and 4 (Q1, Q2, Q3, Q4).

A:

Q: A rectangular canal is 2.5 meters wide. The flow rate via the canal is 378 m/s, with a 3.3 cubic m/s…

A: Given data 2.5 m wide canal Velocity of flu is equal to 378 m per second Discharge is equal to 3.3…

Q: Two tanks A and B. of constant cross-sectiona rea of 10 m² and 2.5 m², respectively, are onnected by…

A:

Q: Water flows from a lake into a steep rectangular channel 3 m wide. Determine the lake level above…

A:

Q: 6.2. A 10-m wide, rectangular, concrete-lined canal has a bottom slope of 0.01 and a constant-level…

A: Data given B = 10 m S = 0.01 y = 6 m Find: (a) flow depth 800 m downstream of canal entrance (b)…

Q: What is the depth of the flow (m) in a circular channel of diameter 2.0 m for the maximum velocity?

A: given dia of circular channel-D= 2 m

Q: If a given 1.8-m diameter culvert conveys water at a depth of 160 cm, then: Calculate the flow…

A:

Q: 2) You are responsible from the planning and design of a water reservoir. As shown below, the…

A:

Q: Diagram of the problem, necessary formulas, clearance and numerical solution A swimming pool whose…

A:

Q: If the head loss in an 8 km long cast iron pipe carrying water at a rate of 1.42 m^3/s is not to…

A:

Q: A concrete-lined drainage canal (ε = 0.08 in) is to be constructed to carry water at a maximum rate…

A: Given: Concrete-lined drainage canal Flow rate, Q = 105 GPM Cross-section of the channel =…

Q: m? Select an answer and submit. For keyboard navigation, use the up/down arrow keys to select an…

A:

Q: A rectangular canal is designed to carry 5 cu.m./s at a velocity of 1.8 m/s. For a most economical…

A: Q= 5 cu m/s Velocity = 1.8 m/s Cross sectional area = by= 5/1.8= 2.778 m2. for most economical…

Q: See attached please and thank you!!

A: To solve this problem, we need to perform iterative calculations to find the flow rates in each pipe…

Q: wo reservoirs having difference in water levels as 12m are connected by a pipe line 3 km long and 30…

A:

Q: Two wells are located at points A and B respectively. Point C is the middle point between A and B.…

A: draw down at C is 7 inches

Q: Two people are arguing on the flow regime of water in a certain trapezoidal canal with the following…

A: Q = 0.09m3 /s

Q: flows at 2.08 cm/s. At a second point downstream, but on the same level, the canal is 16.21 m wide

A: at point A b1 =18.74 m y1 = 3.79 m  v1 =  2.08 cm/ s   at point B b2 =  16.21 m  y2 =  v2 = 10.8…

Q: A pump having the characteristics curve is given below delivers water from a river at elevation 52 m…

A: D = 350 mm or 0.35 m L = 2000 m f = 0.022

Q: The water passes through a rectangular notch in the weir that is 1.5 meters wide and the height of…

A:

Q: The flow through a rectangular channel (width in x and height in z) is nonuniform in the…

A:

Q: What is the depth of the flow (m) in a circular channel of diameter 2.0 m for the maximum velocity?

A:

Q: design the cylindrical wall of an OHSR with M35 grade concrete and fe500 grade of Steel.. the…

A: The above problem is designed as per the hope tensions  The hope tension is the stress which occurs…

Q: 665 li/s, calculate the following. Discharge through pipe 1, discharge through pipe 3 Elevation of…

A:

Q: , wastewater treatment plant (Fig. 5). Given that the v is hi = 0.8 m, calculate the corresponding…

A: Assumptions : Flow is steady  irrotational flow Cd=0.98 Flow is continuos

Q: Answer only that first question thanks. A rectangular canal 3.2 m wide and 1.2 m deep has a full…

A: The objective of the question is to find the slope of the channel bed of a rectangular canal given…

Q: A 10-ft^2 hydraulic conduit issued 10 ft^3/s of flow. When the discharge was doubled, the flow…

A: Given :

Q: 7. How can the dimension of a conveyance canal such as bottom width and depth be influenced by soils…

A: Ans7) Dimension of any hydraulic structure plays an important role. Therefore, while designing any…

Q: Three reservoirs Z, Y, and X meet at Junction P. Reservoir Y (25m above Reservoir X) is at Elev.…

A: