A flow is described by the flow field of V = A(1 + Bt)î + Ctyĵ, where A=1 m/s, B=1 s-¹, and C=1 s². The unit for the coordinates is meters. a. Plot the pathline that passes through the point (x=1 m, y=1 m) at time t=0 b. Compare the streamlines through the point (x-1 m, y=1 m) at time t=0, 1, and 2 s C. Calculate the acceleration at time t=0 along the streamline passing the point (x=1 m, y=1 m) at time t=0

A flow is described by the flow field of V = A(1 + Bt)î + Ctyĵ, where A=1 m/s, B=1 s-¹, and C=1 s². The unit for the coordinates is meters. a. Plot the pathline that passes through the point (x=1 m, y=1 m) at time t=0 b. Compare the streamlines through the point (x-1 m, y=1 m) at time t=0, 1, and 2 s C. Calculate the acceleration at time t=0 along the streamline passing the point (x=1 m, y=1 m) at time t=0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows through a venturi as shown in the figure at a flow rate of Q=1.3L/s. The inlet and throat diameters of the venturi meter are (D = 3.0 cm andd = 2.5 cm) respectively. The height of water column in the manometers L1 and L3 are 65 and 53 cm respectively. %3D What is the experimental dynamic head at the throat-{section2} (in m)? L3
6 Consider a fully developed laminar flow of a fluid through 8027 m long and 4 cm diameter horizontal and circular pipe. The dynamic density and the viscosity of the fluid are 1252 kg/m³ and 0.3073 kg/(m.s). The velocity profile at a cross-section is given by: u(r)= 6[1 − ( 7 )²] - m/s Where r is the axial distance from the centre and R is the radius of the pipe. Determine the following: (i) (ii) the maximum velocity at a cross-section of the pipe, Umax the average velocity at a cross-section of the pipe, Vave the volume flow rate, Q (iv) Reynolds number, Re (v) friction factor, f (vi) head loss, hi (vii) pressure loss, AP (viii) pumping power required, (ix) for the same pumping power, the percentage decrease of the flow rate if the pipe is inclined 10° upward (assume the head loss, hò, calculated in part (vi) does not change) Useful formulae: 64 f Re h₂ = f ( =) ( 2² ) 2g =
A velocity vector in a flow field is given by, 3x2 V = - *i+ 2j + 3yk where V is in m/s and the coordinates are measured in meters. a. Making necessary calculations and/or stating your reason, classify this flow: 1-D, 2-D or 3-D? Steady or not steady? Compressible or incompressible? b. Obtain an equation for the streamline in x-y plane that passes through the point (x,y)=(2,1). c. Is the flow uniform or non-uniform? State your reason by making necessary calculations.
a channel is arranged to drain water, where the shape of the channel is given by y = zx ^ 2 and the velocity is given by v = 4.43 (Lf (x)), find the amount of flow that circulates through the channel per unit of time, if L = 0.64m, a = and m = 800mm 200mm f(x) m.
z=174 m A B z=152 m z=91 m T = and Op ≈pg əx (Pump) C F A pump is used to deliver water from a reservoir to a large tank for a flowrate of 1310 L/s at 20 °C. The connecting pipe connects the reservoir at B with a square-edged entrance. From B to C, the pipe is 760 m long and has three gate valves, four 45⁰ elbows, and two 90° elbows. Gage pressure at C is 197 kPa. From F to G, the pipe is 760 m long and contains two gate valves (Kg.-0.136), four 90° elbows (K90-0.51) and connects the tank with an exit (Kext=1). All pipe is 508 mm in diameter (D) and made by cast iron ( = 0.26 mm). 1) Calculate the average velocity of water in the pipe. 2) Calculate the gage pressure at F. z=104 m 3) If the pump's efficiency is 80%, calculate the power input to the pump. 4) If the shear stress can be calculated using the equation D Op hL major 4 0x L Calculate the average wall shear stress in section F-G. G H
If you decide to help, please help with all the parts of the question, I'm not sure I understand any of it... :/ The tank shown in the following figure is being filled by Pipes 1 and 2. The water level is to remain constant. A tank of water is open at the top. The tank is filled from above by pipe 1 and pipe 2. Pipe 1 has diameter d1 = 1 in., and fills the tank with water at a velocity of V1 = 2 ft/s. Pipe 2 has diameter d2 = 1.25 in., and fills the tank with water at a velocity of V2 = 1.4 ft/s. Water empties from the bottom of the tank through pipe 3. Pipe 3 has diameter d3 = 1.5 in., and empties water from the tank at an unknown velocity V3. (a) What is the volume flow rate (in ft3/s) of Pipe 1? (b) What is the volume flow rate (in ft3/s) of Pipe 2? (c) What is the volume flow rate (in ft3/s) of water leaving the tank at 3? (d) What is the cross-sectional area (in ft2) of flow for Pipe 3? (e) What is the average velocity (in ft/s) of the water leaving the tank?
Make it
how do you derive these equations? pls explain
Water is flowing in a rectangular channel with a base of 4.0 ft. The velocity gradient from the bottom of the channel to the water surface is given by the equation: v=3.5y^0.6 Where y is the distance from the bottom of the channel. The total depth of the flow in the channel is 3.0ft. a) Graph the velocity profile from the bottom of the channel to the water surface. B) Calculate the flow rate by integration. The first step is to draw a cross-section of channel and on that cross-section, Draw on your figure an elemental area DA that you will then ise in the equation: Q=integral V.dA
18) A circular tank of diameter 1.25 m is filled with water up to a height of 5 m and an orifice of 50 mm diameter is provided at its bottom to empty it. Determine the height of water above the orifice after 1.5 minutes if the tank starts emptying. Take Ca = 0.62
Three reservoirs A, B and C are interconnected by pipes as shown in the given figure, Water surface elevations in the reservoirs and the piezometric level at the junction D are also indicated in the figure EL.200 A Piezometric level = 160 고 Q₁ EL. 180 ▼ D B Q3 Flows Q₁, Q₂ and Q3 are related as EL.120 ▼ с