A pipe line of 5 cm diameter is reduced abruptly to 2.5 cm diameter at a section to enable measurement of the water flowing through it. The loss of head at the contraction is 0.5 m. Given that, in metric units, √√√2g = 4.43 and √g = 3.132. The mean velocity in the reduced section will be (Take Cc = 0.585)

A pipe line of 5 cm diameter is reduced abruptly to 2.5 cm diameter at a section to enable measurement of the water flowing through it. The loss of head at the contraction is 0.5 m. Given that, in metric units, √√√2g = 4.43 and √g = 3.132. The mean velocity in the reduced section will be (Take Cc = 0.585)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

L = 700m 4 L = 800m D = 40cm D = 45cm L = 600m L = 700m %3D D = 35cm D = 35cm %3D 0 1 6. A L = 700m В D = 40cm %3D L = 1200m 3 D = 40cm Water is flowing from point A to point B in the system shown in the figure. All the corresponding length and diameter of each pipe is shown. Assuming that each pipe has n=0.011 and head loss from point A to B is 30m, determine the a) discharge at pipe 1 b) discharge at pipe 3 c) discharge at pipe 5 A) Q1 = 0.279 cu.m/s В Q3 = 0.132 cu.m/s C) Q3 = 0.186 cu.m/s D) Q3 = 0.160 cu.m/s E Q1 = 0.320 cu.m/s F Q3 = 0.103 cu.m/s G Q5 = 0.0921 cu.m/s %3D H) Q5 = 0.0581 cu.m/s Q5 = 0.126 cu.m/s () Q1 = 0.253 cu.m/s J Q5 = 0.0777 cu.m/s L) Q1 = 0.216 cu.m/s
شمب Hydrology
A sluice gate, as shown in figure 01, is used to control the upstream water level in a3 m wide rectangular channeL The water discharge in the channel is 15 m3/s. Use the Froude number to show that the clitical velocity at yc is given as Uc = .sqrt(gyc)
Oil flows through a 100 mm diameter horizontal steel pipe, friction factor is 0.0220 of length 400m. The volumetric flow rate is 0.1 m3/s. Find head loss due to friction. Take g= 9.81
3. A tank to form a frustum of a right circular cone 1.50m in diameter at the bottom, 3m diameter at the top, 3.5m high, is full of water. A sharp edged orifice with C=.62 is located at the bottom of the tank. What diameter of orifice is needed to empty the tank in 8 minutes?
5.
In a sudden enlargement of a pipe cross-section, if the velocity of flow at the inlet of pipe (V1) = 40 m/s, velocity of flow at the outlet of the pipe (V2) = 20 m/s and the acceleration due to gravity is assumed to be 10 m/s2, then the loss of head due to sudden enlargement of pipe is: a. 18 m of water b. 40 m of water c. 15 m of water d. 20 m of water
m4
The three-cistern system in the figure contains water. If L1= 2000 m, f 1= 0.013, D1 = 1m; = 2500 m, f = 0.023, D3 = 1.20m. L2 E 2300 m, f2 = 0.02, D2 = 0.60m; and L3 100 m Datum Compute 02 in m³/s. Express your answer in 3 decimal places. 20 m 120 m K
complete solution with illustration, thanks.
Oil flows through a 100 mm diameter horizontal steel pipe, friction factor is 0.0220 of length 400m. The volumetric flow rate is 0.1 m3/s. Find head loss due to friction. Take g= 9.81
Q4