An arteriole has a diameter of 2.5x10-5 m and blood flow rate of 2.7x10-3 m-s-1. Calculate the pressure drop, AP, from one end to the other if the length of the arteriole is 4.9x10-3 m. (The density of blood is about 1.06 g-cm-3. Assume that the viscosity of blood is 0.0040 N-s-m-2.) 4.0 5.52e13 XN-m-2

Q: time needed for a glycine molecule

A:

Q: A small crystal of potassium permanganate (orange) and methylene blue (blue crystal) are placed on…

A: The Methylene Blue  is more complex, heavy.

Q: 11. 22.4 kg/L to dag/mL 12. 0.74 miles/min to dm/sec 13. 1.42 g/em² to mg/mm?

A:

Q: For whole blood flowing in a capillary of radius 1.9x10-4 cm, estimate the maximum velocity for…

A:

Q: ghs 68 kg is 45 years old and has severe hypomagnesaemia. m sulfate heptahydrate to be given…

A: According to the question, Jack who weighs 68 kg is 45 years old and has severe hypomagnesaemia. He…

Q: Oxidised chromium Cr2O3 has a diffusion coefficient of 5 ×10−15 cm2s−1 at 730 ℃ and is 2 ×10−9…

A: Introduction: The diffusion coefficient is defined as the measure of the mobility of the diffused…

Q: Part C (solvents labeled C): How does the number of hydrogen bonding sites within a molecule affect…

A:

Q: Consider 8.5 kg of austenite containing 0.52 wt% C, cooled to below 727'C (1341'F). (a) What is the…

A: Given that, 8.5 kg of austenite containing 0.52wt% C, cooled to below 727°C (1341°F).

Q: A layer of 10 g of iodine is spread uniformly over a surface of area 10 cm? and covered in hexane to…

A: Given: Mass of iodine= 10g Area = 10cm3 Depth = 10 cm Diffusion coefficient = 4.04 * 10-9 m2/s To…

Q: Question-2 A) The diffusion coefficient for glucose in water is 6.81x10*10 m²s' at 25 °C. The…

A:

Q: The interfacial energy γoil-water of an oil – water interface at 25 oC is 53 mJ/m2. The surface…

A: The ability of one liquid to spread over the other liquid is known using spreading coefficient. For…

Q: Si crystalizes into a diamond crystal structure with lattice constant a = 0.543\: nma=0.543nm.…

A: Given:Si crystalizes into a diamond crystalstructure with lattice constant a=0.543 nmwe have to…

Q: Reforences Use the References to access important values if needed for this question. Copper has a…

A:

Q: 1. The density of ice at 0°C is 0.9168 g mL-1, and that of liquid water at 0°C is 0.9999 g mL-. (1)…

A: Density of a substance is defined as mass of substance per unit volume. SI unit of density: kilogram…

Q: Q4)A silicon wafer is doped with 10^21 phosphorus atoms / m^3. Find the carrier concentration and…

A: Given: Nc = 2.8 × 1025 m-3 Ni = 1.5×1016 m-3 Phosphorous is dopant.

Q: What is the diffusion coefficient of a membrane-bound protein of molar mass 79,300 daltons at 37°C…

A: The exact solution is given below

Q: True o

A: In this question we have to explain that The above statements are true or false with suitable…

Q: Predict the temperature at which CuSO4:5H2O undergoes dehydration. CuSO4:5H20 (s) CUSO4 (s) + 5H2O…

A: At equilibrium,the change in free energy is zero. The given reaction is at equilibrium. But ,

Q: What is the mole fraction of magnesium nitrate, Mg(NO3)2, in an aqueous solution that is 5.549 wt %…

A:

Q: PV = nRT. The pressure is 0.9912atm.  V = 50.5 mL.  T = 21.5°C and n = 0.00200mol.   Calculate R…

A: We have to calculate the R that is gas constant.

Q: (g) The material 60-40 Solder contains 60 wt% Sn and 40 wt% Pb. Calculate the composition of the…

A:

Q: 20. 25 m/s to miles/hr

A: Unit conversion: (20) 25 m/s to miles/hr As we know that; 1 mile=1609.344 m1 m=11609.344mile…

Q: A water molecule at 25ºC carries out an average displacement of 0.037 cm. after 10 seconds. At 120ºC…

A: The objective of the question is to calculate the diffusion coefficient and the average displacement…

Q: Regarding the rate of creaming of pharmaceutical emulsions, which of the following statements are…

A: Pharmaceutical emulsions are suspensions of small droplets of one liquid dispersed in another…

Q: The correct representation of the variation of molar conductivity (y-axis) with surfactant…

A: Molar conductivity is a measure of a solution's ability to conduct electricity, expressed as the…

Q: Define the flux, J, of a property and describe the rate of migration of a property by flux J, in…

A: In simple words, the concept that a solute will move from a region of high concentration to region…

Polymerization Kinetics

Polymerization is a chemical process in which one or more monomers combine to produce a very large chain-like molecule called a polymer. The functional groups present on the monomers and their steric effects are responsible for polymerization through a sequence of reactions that diverge in complexity. There exists a stable covalent chemical bond between monomers that sets apart polymerization from other processes. Polymerization is generally classified into step-growth and chain polymerization. Polymers are categorized into linear polymer and cross-linked polymers that are produced either by condensation or additional polymerization.