An aluminum sphere, initially at a temperature of 25°C, is placed in a 300°C oven. How do the temperatures of the sphere center (black) and the sphere surface (orange) change over time? Assume that the thermal conductivity of the sphere is large and that the rate of convective heat transfer to the sphere is relatively small. Why? A B Tourface Tinside Time Time E D Time Time Time Temperature Temperature Temperature Temperature Temperature

An aluminum sphere, initially at a temperature of 25°C, is placed in a 300°C oven. How do the temperatures of the sphere center (black) and the sphere surface (orange) change over time? Assume that the thermal conductivity of the sphere is large and that the rate of convective heat transfer to the sphere is relatively small. Why? A B Tourface Tinside Time Time E D Time Time Time Temperature Temperature Temperature Temperature Temperature

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Using a polynomial equation solver, determine the steady-state surface temperature (Ts) of the passive radiative cooler below that is exposed to a windy convective enviroment h=40 W/m2*K and T∞= 25°C. The surrounding atmosphere is fixed at Tsur= 10°C. Set up the energy balance/conservation equation.
PROBLEM 4: A black thermocouple is inside a chamber with black walls. If the air around the thermocouple is at 20°C, the walls are at 100-C, and the heat transfer coefficient between the thermocouple and the air is 75 W/m²K, what temperature will the thermocouple read?
a. What does it mean when we say that a surface 'sees itself' in the context of radiative heat transfer? b. If heat transfer by conduction through a medium occurs under steady- state, will the temperature at a particular location vary with time? Will the temperature vary with location in the medium?
A manufacturing facility located at 32° N latitude has a glazing area of 60 m² facing west that consists of double pane windows made of clear glass (SHGC = 0.766). To reduce the solar heat gain in summer, a reflective film that will reduce the SHGC to 0.35 is considered. The cooling season consists of June, July, August, and September, and the heating season, October through April. The average daily solar heat fluxes incident on the west side at this latitude are 2.35, 3.03, 3.62, 4.00, 4.20, 4.24, 4.16, 3.93, 3.48, 2.94, 2.33, and 2.07 kWh/day · m² for January through December, respectively. Also, the unit costs of electricity and natural gas are $0.09/kWh and $0.45/therm., respectively. If the coefficient of performance of the cooling system is 3.2 and the efficiency of the furnace is 0.90, determine the net annual cost savings due to installing reflective coating on the windows. Also, determine the simple payback period if the installation cost of reflective film is $20/m². Answers:…
Pravinbhai
A long, horizontal, cylindrical steel reactor, 1 m in diameter, has a surface temperature of 300ºC. The emissivity of the steel is 0.6, and the heat transfer coefficient for natural convection is 5 W m−2 K−1 . Heat is lost by convection to the air at 15ºC, and also by radiation to the surroundings, which can be considered to be a black body at 15ºC. a) Calculate the total heat loss per metre length of the reactor, and the proportions lost by convection and radiation b) The reactor is then insulated with a thin layer of insulation material to reduce the total heat loss to one-tenth of its original value. This causes the surface temperature of the steel to rise to 400ºC. The thermal conductivity of the insulation is 0.01 W m−1 K−1 , and its surface emissivity is 0.2. Show that the resulting surface temperature of the insulation is about 89ºC, and calculate the thickness of insulation required, stating any assumptions made. Specifically need help with part b
If the node temperature of the following element is(image 1) Determine the temperature at point (2,2) in question no 1 of figure c, and the coordinates (4,3) for question no 1 (d).(image 2)
What is visual perspective? What is foreshortening? Why is foreshortening important in perspective? Explain with a visual example
Question 11 Not yet answered Marked out of 2.50 P Flag question A cylindrical resistor element on a circuit board dissipates 0.23 W of power in an environment at 28°C. The resistor is 1.3 cm long, and has a diameter of 3 mm. Assuming heat to be transferred uniformly from all surfaces. What is the surface temperature of the resistor for a combined convection and radiation heat transfer coefficient of 13 W/m .°C? Select one: A. 157.46 B. 190.22 C. 168.73 D. 130.79 E. 143.48
4. The surface temperature of a planet is T, and the measured temperature is Tm (i.e. the temper- ature measured at the top-of-atmosphere based on the upwards flux Ft there). Assume radiative equilibrium. (a) Show that the infrared optical depth of the planet's surface 7 is related to the surface temperature T, and the measured temperature Tm by Calculate the infrared optical depth at the surfaces of (a) Earth, where T, = 300 K and Tm = 250 K. (b) Venus, where T, = 750 K and Tm = 230 K. (c) Mars, where T, = 240 K and T, = 220 K.
After you exercise for a while, you may notice that your skin turns red. (A) How is the blood flow in your limb changes as a response to the exercise? When your skin turns red, how has the temperature changed at the skin surface (Tskin)? (B) During exercise, does the total heat generation rate inside your body increase or decrease from that in normal conditions? (C) What is the relationship between the total heat generation rate and the total heat loss from the skin surface to the environment by convection? Neglect sweating and radiation. (D) The total heat loss from the skin surface to the environment is hA(Tskir-Tair). Based on this convection equation and results in (C), how has the skin temperature changed during exercise? Does Tskin increase or decrease from that in normal conditions? Is this consistent with that in (A)?
29. Gamma radiation is bombarding an iron plate as shown in the figure. A con- vection boundary condition of T;= 150 C and h = 200 W/m-K removes heat from the plate. Find the maximum temperature and its location in the plate. Also find temperature at 1 cm from the side facing irradiation and the rate of heat removal from the side not being irradiated. k= 48.5 kW/m K, µ= 24.6 m'. Questions and Problems 507 40 = 19,600 kW/m³ 15 cm T, = 150 C h= 200 W/m K T = 150 C h= 200 W/m K