An 2014 T-6 aluminium flag pole with a hollow rectangular sectionexperiences a wind force of 750 N at an angle of 30° to the horizontal that750 Ncauses the pole to bend.|30°0,05 ma) Determine whether the strength of the pole is sufficient to withstandthe normal stresses caused by bending.Thickness:0.1 m10 mmb) Find the orientation of the Neutral Axis.4.0 m

ultimate tensile strength : A tensile test is commonly used to determine ultimate tensile strength,…

An 2014 T-6 aluminium flag pole with a hollow rectangular section experiences a wind force of 750 N at an angle of 30° to the horizontal that causes the pole to bend. 750 N 30° 0.05 m a) Determine whether the strength of the pole is sufficient to withstand the normal stresses caused by bending. Thickness: 0.1 m 10 mm b) Find the orientation of the Neutral Axis. 4.0 m

An 2014 T-6 aluminium flag pole with a hollow rectangular section experiences a wind force of 750 N at an angle of 30° to the horizontal that causes the pole to bend. 750 N 30° 0.05 m a) Determine whether the strength of the pole is sufficient to withstand the normal stresses caused by bending. Thickness: 0.1 m 10 mm b) Find the orientation of the Neutral Axis. 4.0 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

etermine the elongation of a 0.5-in, dianeter sterl bar The elastic modulus of the steel bar is 27000 kar. 2000 Ib 10 ft
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v=0.33] pipe has an outside diameter of 200 mm, a wall thickness of 5 mm, and a length of 5.4 m. The pipe supports a compressive load of 670 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 6= i AD= i mm mm
400mm Find the required spacing of intermediate stiffeners if V*=1600KN 25mm • Check the adequacy of a pair of stiffeners 90mmx12mm • Check the web crushing capacity if the reaction of 1600kN is applied over a stiff bearing length of 250mm at the end of the beam (note that the spread of stress can only go in one direction) • Homework extension: Check the adequacy of an endplate stiffener 300 wide by 16mm thick 12mm Use Grade 300 Steel 1440mm
The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0, calculate the maximum load in N that the bar can support. А) 12500-pi в) 6250*pi с) 3125*pi D) 1563*pi
A steel cantilever beam 6 m in length is subjected to a concentrated load of 120 N acting at the free end of the bar. The cross section of the beam is shown below. deep. Determine the magnitude and location of the maximum tensile and compressive bending stresses in the beam. As usual, neglect the weight of the beam. 4mm 120 N 1mm 1mm 6mm 6m 1mm 4mm
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 215 mm, a wall thickness of 12 mm, and a length of 4.3 m. The pipe supports a compressive load of 695 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i AD = i mm mm
11. Iwo beams, one having square cross section and another circular cross-section, are subjected to the same amount of bending moment. If the cross-sectional area as well as the material of both the beams are same then (A) Maximum bending stress developed in both the beams is the same (B) The circular beam experiences more bending stress than the square one (C) The square beam experiences more bending stress than the circular one (D) As the material is same both the beams will experience same deformation
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 270 mm, a wall thickness of 15 mm, and a length of 5.5 m. The pipe supports a compressive load of 635 kN. After the temperature of the pipe drops 45°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = i AD= i mm mm
A hollow titanium [G = 43 GPa] shaft has an outside diameter of D = 46 mm and a wall thickness of t = 1.23 mm. The maximum shear stress in the shaft must be limited to 118 MPa. Determine: (a) the maximum power P that can be transmitted by the shaft if the rotation speed must be limited to 22 Hz. (b) the magnitude of the angle of twist in a 830-mm length of the shaft when 17 kW is being transmitted at 9 Hz. Answers: (a) P = (b) = i kW. O
A solid steel tube must carry a tensile load of 40KN. Determine the diameter of the tube if the stress is limited to 120 Nm/m²
It is required to deisgn a close coiled helical spring which shall deflect10 mm under an axial load of 100 N at a shear stresss of 90 N/mm². Modulus of rigidity is 8 x 104 MPa. The mean diameter of the coils is 10 times diameter of the wire. Find the diameter and length of the wire necessary to form the spring.
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v=0.33] pipe has an outside diameter of 225 mm, a wall thickness of 15 mm, and a length of 5.0m. The pipe supports a compressive load of 670 kN. After the temperature of the pipe drops 48°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = mm AD= i mm