: An 2.44 m span cantilever beam has a rectangular section and reinforcement as shown in Figure. The beam carries a dead load including its own weight of 2 kN.m and a live load of 1.22 kN.m. Using fy = 414 MPa and f. = 27.58 MPa , check if the beam is safe to carry the above loads. 3 # 7 2.44 m 460 mm 396 mm

: An 2.44 m span cantilever beam has a rectangular section and reinforcement as shown in Figure. The beam carries a dead load including its own weight of 2 kN.m and a live load of 1.22 kN.m. Using fy = 414 MPa and f. = 27.58 MPa , check if the beam is safe to carry the above loads. 3 # 7 2.44 m 460 mm 396 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 3m-LONG CANTILEVER BEAM IS CARRYING A UNIFORM DEADLOAD OF 20 kN/m (EXCLUDING SELFWEIGHT OF THE BEAM), AND A LIVE LOAD OF 15 kN/m. OTHER GIVEN: fc = 27.5 MPa fy = 414 MPa b = 300mm h = 600mm diameter of main reinforcements, db = 25mm diameter of transverse reinforcements, ds = 12mm use clear concrete cover of 45mm unit weight of concrete is 25kN/m3 Solve for the following: a. Reactions at the fixed support. b. Maximum FACTORED moment of the beam, Mu c. Effective depth of the beam d. As required e. No. of 25mm reinforcements required to resist Mu f. Spacing of stirrups at the critical location (d from face of the support) - use manual calculations, show your solutions.
A concrete beam has a cross sectional area of 275mmwidth and 150mm height for the upper flange. While thelower flange has 450mm width with a 150mm height. If theflange has length of 225mm while 200mm width,determine the centroid and the moment of inertia of thegiven structure. answer this ASAP. Please thank you
A fully braced steel beam consisting of A-36 steel is used as a simple beam for a span of 6 m. It caries equal concentrated loads of 80 kN at each quarter of the beam. E= 200 000 MPa. Fy 250 MPa. A = 14000 mm? d = 360 mm br = 256 mm tr = 19.9 mm tw = 11.4 mm Properties of Steel Beam k= 331 x 10 mm4 ly = 55.7 x 106 mmª Sx = 1840 x 103 mm3 Sy = 435 x 103 mm³ additional uniformly 2 Determine distributed load that the beam can carry if the compression flange has lateral supports only at its ends. the
A simply supported rectangular beam of length 6.45m has a width of 390.5mm and an effective depth of610.5mm. The beam is to be reinforced using 12 ?? bars. The beam supports service dead loads ofWd = 13.5kN/m and WL = 35.5kN/m. f'c = 28Mpa and fy=420 MPa Given: b= 390.5 mm d= 610.5mm L= 6.45 m Wd = 13.5 kN/m WL = 35.5 kN/m 1. Calculate the ultimate moment capacity of the beam.2. Calculate the height of the equivalent stress block.3. Determine the number of bars required for this beam.
a beam b = 350mm h = 660mm is reinforced with 2- 28mm compression bars and 4- 36mm tension bar. concrete cover is 60mm from centroid of the bar, if The beam is subjected to a maximum service dead load of 230KN m. determine the maximum service live load the beam can carry. use fc = 21Mpa, fy = 345MPA Select the correct response: MII = 244.02KN-m MII = 390.43KN-m %3D MII = 666.43KN-m MII = 436.43KN-m
simply supported beam AB has a length of 3 m and carries distributed load which varies in linear manner from (1w) N/m at A support to (2w) N/m at the B support and concentrated load (1.5w) N at 2 m from A support, and the beam has hollow circular cross section of diameter ratio diu/dow =1/3. Draw S.F. and B.M. diagrams for the beam and determine the value of (w) if the maximum bending stress 110 Nam?, and the average shear stress at 1 m from point A equal to 15 N/m. COMPANY
Plz, solve this problem using Flexibility method and show all the steps one by one and draw SFD and BMD Structural Analysis-2
Need help asap pls.
AW 21 x 93 A36 steel is used for a cantilever beam with a span of 5.0m PROPERTIES OF W 14 x 132 A = 17 600 mm? , = 862 x10 mm d = 549 mm 4 = 38.7 x10 mm tw = 14.7 mm bị = 214 mm t, = 23.6 mm The beam is used to carry a distributed dead load of 60kN/m and a distributed live load of 75KN/m A. Determine the shear flow at neutral axis. B. Determine the allowable shear capacity of the section using ASD NSCP 2001 C. Determine the design shear capacity of the section using LRFD NSCP 2015
DO NOT ROUND OFF IN BETWEEN SOLUTIONS.