Among the test coupon you were provided with, which material hasthe highest potential for strain hardening? This means the yield strength ofthe material can be improved, as a percentage of its current yield strength,by the largest margin. Justify your answer.temHIPSnylon 6 (fiber)ABSpolypropyleneTensile strength52 MPa63 МРа44 MPa34 MPаExperimental Modulus of885 MPa980 MPа950 MPa480 MPаelasticityCross Sectional Area2.482 mm?2.482 mm?2.482 mm?2.482 mm?Tensile elongation at break100-200%12-16%80-110%100 - 650%

Among the test coupon you were provided with, which material has the highest potential for strain hardening? This means the yield strength of the material can be improved, as a percentage of its current yield strength, by the largest margin. Justify your answer. Item HIPS nylon 6 (fiber) ABS polypropylene Tensile strength 52 MPa 63 MPa 44 MPa 34 MPa Experimental Modulus of 885 MPa 980 MPa 950 MPa 480 MPa elasticity Cross Sectional Area 2.482 mm2 2.482 mm2 2.482 mm? 2.482 mm? Tensile elongation at break 100-200% 12-16% 80-110% 100 - 650%

Among the test coupon you were provided with, which material has the highest potential for strain hardening? This means the yield strength of the material can be improved, as a percentage of its current yield strength, by the largest margin. Justify your answer. Item HIPS nylon 6 (fiber) ABS polypropylene Tensile strength 52 MPa 63 MPa 44 MPa 34 MPa Experimental Modulus of 885 MPa 980 MPa 950 MPa 480 MPa elasticity Cross Sectional Area 2.482 mm2 2.482 mm2 2.482 mm? 2.482 mm? Tensile elongation at break 100-200% 12-16% 80-110% 100 - 650%

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel solid is subjected to following set of principal stresses: 01 = 300 MPa and o2 = 250 MPa. Assuming u = 0.25 and elasticity modulus as 2 x 10 MPa, calculate the strain energy per unit volume in N-mm. (Round off to 2 decimals places).
A sample of aluminum is stretched by a 6 kip load. If the aluminum piece is 30 inches long, 2 in^2 in area, what is the deformation of the sample in inches? Answer to three decimal places. Type your answer...
During laboratory testing of an 6-inch aluminum-alloy rod with a cross sectional area of 0.32in², a tensile load of 50,000 lbs.is applied. Ifthe cross sectional area decreases to 0.3188in? and lengthens to 6.022 inches, what is the Modulus of Elasticity and Poisson's Ratio? E = 6/ɛ V = = -E(lateral)/ɛ(axial)
8)
What is the most common fiber material in fiber-reinforced plastics?
10 Which is not an elastic constant? Bulk modulus Shear Modulus none of the choices Modulus of elasticity
An ASTM A615 grade 60 number 10 rebar with a gauge length of 8 in. was subjected to tension to fracture according to ASTM E-8 method. The load and deformation data were as shown in Table .Using a spreadsheet program, obtain the following:a. A plot of the stress–strain relationship. Label the axes and show units.b. A plot of the linear portion of the stress–strain relationship. Determine modulus of elasticity using the best-fit approach.c. Proportional limit.
A sample of a steel alloy has a yield strength of 560 MPa, ultimate tensile strength of 630 MPa, and Young's modulus of 200 GPa. a) What is the maximum load that can be applied to a sample with a square cross-section of 10.0 mm by 10.0 mm without plastic deformation occurring? b) If the original sample length prior to testing was 63 mm, what is the maximum length that it can be elongated to without causing plastic deformation? c) What is the difference between elastic strain and total strain?
Please give me answer immediately
Q2: Comparison between the following? (Choose one only) 1. Ductility and toughness of a materials property? 2. Permeability and porosity property?
(a) the modulus of elasticity in GPa for the Aluminum B) the proportional limit in MPa for the Aluminum C) the ultimate strength in MPa for the Aluminum D) Ductility of material based on percent elongation
ANSWER THE PROBLEM GIVE WHAT IS ASKED, SHOW YOUR SOLUTION, AND BOX THE FINAL ANSWERS. WRITE IT ON A CLEAN PAPER CLEARLY. I WILL GIVE THE FEEDBACK RATING AS POSSIBLE, YOU CAN ANSWER IT. THANK YOU