Air enters a multistage compressor of a jet engine at 0.65 atm and 275 K with a flow rate of 63.5 kg/s. The compressor has an overall pressure ratio of 24:1 and an isentropic efficiency of 94%. Deter- mine the power required to drive the compressor and the temperature of the air at the compressor outlet. P=0.65 atm T = 275 K rit = 63.5 kg/s Wn?

Air enters a multistage compressor of a jet engine at 0.65 atm and 275 K with a flow rate of 63.5 kg/s. The compressor has an overall pressure ratio of 24:1 and an isentropic efficiency of 94%. Deter- mine the power required to drive the compressor and the temperature of the air at the compressor outlet. P=0.65 atm T = 275 K rit = 63.5 kg/s Wn?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Note:- • Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism. • Answer completely. • You will get up vote for sure.
An air turbine operates with P₁ = 1200 kPa and T₁ = 1500 K at the inlet, an inlet area of A₁ = 0.1 m², an inlet velocity of V₁ = 15 m/s, an exit pressure of P₂ = 100 kPa, and an isentropic efficiency of n = 90%. Complete a thermodynamic analysis of the turbine, assuming the specific heats are constant with k = 9/7, by finding: (A) The temperature at the exit, T2, (B) the mass flow rate through the turbine, m, (C) the work produced by the turbine, Wr, and (D) the rate of entropy production in the turbine, Šgen. Plot the process on a T-s diagram and clearly label states 1, 2s, and 2. WT
A three stage, single-acting air compressor with a polytropic index of 1.22 in all stages, runs in an atmosphere at 101.3 kPa and 25°C. It has a FAD of 4.2 m^3/min with a delivery pressure of 1.8 MPa. Induction occurs at 92 kPa and 34°C. The mechanical and motor-drive efficiencies are 80% and 93% respectively. Assume complete inter-cooling and neglect clearance volume. Cp= 1.006 kJ/kg K Cv= 0.717 kJ/kg K 1) which formula should be used to calculate the temperature of the air at entrance to the 2nd intercooler? 2) calculate the temperature of the air at entrance to the 2nd intercooler in the presentable unit? 3) which formula should be used to calculate the rate of heat rejected in the 2nd intercooler?
What is the difference between the clearance volume and the displacement volume of reciprocating engines?
10. An ideal single air compressor without clearance takes in air at 100 kPa with a temperature of 16°C and delivered it at 413 kPa after isentropic compression. What is the discharge work done in kJ/kg? (ME Board: April 1998)
In a gas-turbine plant working on a Brayton Cycle, the air at the inlet of the compressor is at 25C (298.15 K) and 100 kPa. The pressure ratio (PB/PA=PC/PD) is 6.50 and the maximum permissible temperature in the turbine is 800C (1073.15 K). Consider CP = (7/2)R and CV = (5/2)R and n = 1 mol Determine the following of the ideal air cycle: (adiabatic reversible compression and adiabatic reversible expansion). Express heat and work in Joules. Thermal efficiency of the ideal air cycle
Temperature, Pressure and Volume of air (Y=1.4) at the end of isentropic compression in an air standard Carnot heat engine cycle are 315.6 °C, 120 kPa and 0.05 m³ respectively. The volumetric ratio of the isothermal expansion (2-3) and that of isothermal compression ( V₁ ¹₁-3). The volumetric ratio the isentropic expansion (¹-6) and that of isothermal V/₂ compression (¹= 6). (Please draw a P-V diagram of the Carnot cycle) V₁ Calculate; a) The pressure, minimum Temperature and volumes of other states of the Carnot cycle. [ + b) The heat supplied and rejected by the cycle c) The efficiency of the cycle 星

Q3→ Steam enters a steam turbine at a pressure of 4 MPa and a flow rate of 25 kg / s at 450 ° C. At a pressure of 1 MPa and a temperature of350 ° C, intermediate steam is drawn from the turbine at a flow rate of 5 kg /h. The remainder of the steam leaves the turbine at 10 kPa pressure and 0.90 dryness. 200 kW of heat loss occurs from the turbine to the environment. Ambient temperature is 25 ° C and pressure is 100 КРа. www a) Calculate the exergy (available work potentials) of the state points. b) Find the reversible amount of work and the actual amount of work during this process. c) Calculate the amount of irreversibility (exergy destruction) in this process. d) Calculate the second-law yield for this process.
In a gas-turbine plant working on a Brayton Cycle, the air at the inlet of the compressor is at 25C (298.15 K) and 100 kPa. The pressure ratio (PB/PA=PC/PD) is 6.50 and the maximum permissible temperature in the turbine is 800C (1073.15 K). Consider CP = (7/2)R and CV = (5/2)R and n = 1 mol Determine the following of the ideal air cycle: (adiabatic reversible compression and adiabatic reversible expansion). Express heat and work in Joules. A. TB and TD; PB, PC, and PD for these conditionsB. Heat supplied (Process BC)C. Maximum work (WSmax ), minimum work (WSmin) and WnetD. Thermal efficiency of the ideal air cycleE. Thermal efficiency of the air cycle, if the compressor and turbine operate adiabatically but irreversibly with efficiencies and temperatures after the compression and expansion steps
At P = 22 kPa, 0.9 quality steam (H = 2377 kJ/kg) enters a condenser. All of it condenses and the pressure remains 22 kPa. What is the specific enthalpy of the outlet stream?
In an ideal diesel cycle the pressure and temperature at the beginning of the adiabatic compression are 98.5kN/m^3 and 60°c, respectively.themaximum pressure attained during the cycle is 4.5MN/m^3 and the heat received during the cycle is 580kJ/kg gas.Determine for the cycle a) the volume ratio of compression b) the temperature at the end of compression c) the temperature at the end of heat reception d) the temperature at the end of adiabatic expansion e) the net work done/kg of gas f) the thermal efficiency g) the work ratio h) the mean effective pressure I) the Carnot efficiency within the cycle temperature limits.