After exchanging the adjustable one-way flow control valve 1V2 in the control circuit shown the supply port and working port are accidentally interchanged. Which would be the effect of this mistake on the operation of the control circuit? The piston rod of cylinder 1A will retract unthrottled at all times. Both chambers of cylinder 1A will be pressurized and its piston rod will remain in mid-position. After retracting cylinder 1A, it can not be brought in the extended end position anymore. The piston rod of cylinder 1A will be permanently in the forward end position. The piston rod's retracting movement will be throttled. SS In the pneumatic controlled system shown, the cylinder does not retract. Given the following measurements. What could be the possible cause of the malfunction? Cylinder 1A Valve 1V1 O Solenoid coil 1Y2 Adjustable one-way flow control valve 1V2 Adjustable one-way flow control valve 1V3

Q: A motor operates at 1800 RPM and expends 2 HP.  How many ft-lbs of torque does it provide at that…

A: Given data: The speed of the motor is; N=1800 RPM. The power of the motor is; P=2 HP.

Q: When does the reduction in the dimensions occur?

A: Reducing of dimensions is done in the following conditions. Reducing of dimensions of a workpiece…

Q: a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e = 3.0 in. horizontal), Draw the kinematic…

A: Given mechanism:                           Given datalength of link a = 15 inlength of link b = 7…

Q: A seesaw that weights 45lbs and its 5m long is balanced on the fulcrum in the center.  1- Two…

A:

Q: Sorry that's the wrong answer it is 0.62

A: Power coefficient = Cp=0.24 Wind speed = Vw=10.3 m/s Blade length = R = 34 m The power generated by…

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: wy = 1/2 Wy= 98 V = TT R = 4500 by = 0.12346 wx= 102.66 Mechanical V = 2000 x 1000 360 SSS.S کککک…

A:

Q: In the moment calculation, why did you take away the h* from 8?

A:

Q: When does a couple of moment work?

A: A couple is when a system of forces has no net force but has a net moment. A couple causes pure…

Q: An engineer is creating a solid model of a simple gear using SolidWorks. Choose the correct…

A:

Q: 15. On the produced part below, show a simple sketch on how the flatness on the part m verified and…

A: Flatness:- It is defined as the minimum distance between two planes within which all the points on…

Q: What is the v-velocity at the centerline after refining the mesh

A: To explain: What is the v-velocity at the centerline after refining the mesh.

Q: Q1: Use scale (1:1), draw the front, top & side views of shape shown below. (50 M)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: How can we find the location of the neutral axis?

A: When a bending moment is applied on a beam, normal stresses are set up in its cross-section due to…

Q: Assuming there is no wheel slippage, what is the wheel rotation speed in revolutions per minute of a…

A: Given data: The time for car is t=5 min=300 sec The covered distance is s=181 m The diameter of the…

Q: What is a Couple Moment?

A:

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.