Abar having a length of 5 in and cross-sectional area of 07 in is subjected to an axial force of 8000 b Figure - Part A If the bar stretches 0.0010 in determine the modulus of elasticity of the material. The material has linear elastic behavior (1) Submit VAE Ivec Provide Feedback Previous Answers Request Ans X Incorrect Try Again; 4 attempts remaining ki

Q: What is the low limit on the smallest outside diameter?

A: Solution:

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Metal forming processes are the processes in which plastic deformation of the material is done in…

Q: A 1 Cutting Fluids 2 HSS 3 Serrated or segmented chips 4 Vertical shaper 5 Milling B Chip load 7…

A:

Q: A bronze sleeve is slipped over a steel bolt and held in place by a nut that is turned to produce an…

A:

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: If 17 welders can complete a job in 134 hours, how long will it take for 21 welders to do the same…

A:

Q: Choose one of the following statements which is not true.

A: for solution refer below images.

Q: What do you mean by method of section?

A: Methode of the section is used to solve the static equilibrium of the strusses. In this method,…

Q: How much scrap pipe will be left if a 13-ft 6in. piece is cut out of a 20-foot length of pipe?

A: total length of pipe=20'cut piece length of pipe=13'6"

Q: A particle P of mass m = 3 kg arrives at point O with a horizontal velocity and starts rolling down…

A: Given:

Q: 3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made…

A:

Q: Circle all correct statements. Plastic deformation a. Is permanent. b. Is recoverable. c. Can be…

A: Dear student, we are suppose to solve only one question. Please post other question as a separate…

Q: In which of the following casting process, the melting pot is an integral part of the machine. * O…

A:

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: Describe thrust angle.

A: Introduction  The thrust angle is basically used as a major angle for alignment of the rear and…

Q: arc o C.

A: STEP-1 First draw the one arc from origin O1 with radious of 20mm ( AB)  And then draw the another…

Q: 100 mm- 11.5 mm 7.5 mm N A 225 mm 11.5 mm (a)

A:

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: please provide a type written explanation of the topic

A: Solution : Need for us to generate straight line motion

Q: 3. The shaft AB is made from L2 tool steel (shear modulus 75 GPa), has al diameter of 40 mm, and is…

A: Given data  Shear modulus= 75 GPa  Diameter= 40mm Find the maximum shear stress in AB and BC

Q: what is the bottom length?

A: To calculate the bottom length

Q: Learning Goal: To determine the equation for the elastic curve of a beam that is subjected to an…

A:

Q: What is the length and wall thickness of the vertical bear

A: For figure 2,  drawing and the type of symbols present

Q: A 15-meter long beam-tank assembly supports the loading shown in addition to its weight, which is a…

A: The outer diameter of cylinder is .The inner diameter of cylinder is .

Q: Answer the following elating to the drawing in figure (38): 1- What is the name of the component? 2-…

A: A rotational or sliding motion for two parts or maybe more or support an applied load is a shaft…

Q: 1. Uf this drawing? 2. What is the name of the company responsible for the drawing? 2. MILWAVKEE…

A: Given :-  9.The drawings are shown in what angle

Q: What does the shear flow measure?

A: The shear flow is defined as the shear force per unit length in a thin walled perimeter. The…

Q: Using the method of joints, determine the force in each member of the truss shown. State whether…

A:

Q: What is the average force magnitude?

A:

Q: From the following identify the true statement. O In electrical safety precaution, all non-metallic…

A: out of the 4 statements

Q: I have three parts that I need answered pertaining to the print provided below.   What material is…

A: To find the material specified for the part in the drawing, refer Title Block of the drawing.

Q: Q1/B) Match between Column A & B. A 1 Cutting Fluids 2 HSS 3 Serrated or segmented chips 4 Vertical…

A: To match: The column A and B. Given: Cutting fluid also known as emulsified oil. 1. Cutting fluid…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.