17. Interpret the significance of the letters shown in the following illustrations (a through f). FW = a. FW b. A-A = A-A с. G =

Q: Past ME Board The following coa C = 70.5 % S = 3.0% A stocker fired b fuel. Calculate th pressure if…

A: Given: C=70.5%; H2=4.5%; O2=6%; S=3%; N2=1%; Ash=11%; and Moisture=4%.A stocker fired boiler of…

Q: 10 kNim 50 kN Identify the moment diagram of the beam shown. 3125 3125 (AN mA 022 (AN-m)A

A:

Q: PROBLEM 5: The water in a tank is pressurized by air, and the pressure is measured by a multifluid…

A:

Q: 3. Water vapor enters a turbine at p = 4 bar, T1 = 200°C and exits at p2 = 1 bar with a quality of…

A: The superheated steam entered to the turbine expands and dur to this turbine converts energy of…

Q: Match the letter to the correct part description based on the picture of the milling machine below.

A: Milling Machine Parts name

Q: ldentify the valvetrain components in the drawings. Place the identifying letter next to the name of…

A: Valve train get together for a gas powered motor contains a typical transporter which upholds the…

Q: b. If the Farmville community needs 5.5 m/s to sustain its activities, how much water (in m) does it…

A: (b) Write the given data.   QA=20 m3/sQB=30 m3/sQdown=46 m3/s

Q: Write the following as full (decimal) numbers with standard SI units. b. 10cm c 1001 g d. 48cl

A:

Q: 1- The initial velocity of the block in position A is 30 m/s. Knowing that the coefficient of…

A: Dear student, I have derived a general expression for time. You can put any value of theta and get…

Q: Question 1 A horizontal "hot air blower" consists of a fan, an electrical heating element and a…

A:

Q: How many of the following statements about heat and work is/are correct? Heat and work are…

A:

Q: D. T= 310 K, P = 4 kPa Region = ? u = ? E. T = 647.096 K, P = 22.064 MPa Region = ? v = ? F. T 800…

A:

Q: move to the left Can you sce what happens to le motion of the conneting Tod at that point? You can…

A: it is the case of inversion of four-bar mechanism. it is the model representation of single piston-…

Q: 5. Visualize a substance with the following points on the phase diagram: a triple point at 0.5 atm…

A: (d) At 350 K the liquid starts to vaporize to form gas as well as has condensed to liquid i.e. So…

Q: Question 3) On the  plate in the figure, the length  L  is given as L=72 m . According to this;…

A:

Q: A steady stream of air enters a horizontal compressor at the rate of 0.02 kg/s. The air temperature…

A: During a steady-flow process, the total energy content of a control volume remains constant i.e.,…

Q: Interpret the significance of the letters shown in the illustration

A: Instruction given at tail of the welding symbol is "See detail A".Here detail A will have the…

Q: 1) The two forces shown in Figure 1 act on the structural member AB. (A) By using parallelogram law…

A: given;

Q: Q2(a) A box sliding at point B as shown in Figure Q2(a) with acceleration of 3.8 m/s². Assume the…

A:

Q: G. T 800 K, P = 5 MPa Region = ? s = ? H. T 743.2 K, P = 4.61 MPa Region = ? h= ?

A: G: Given Temperature  T=800 K=527°C                 Pressure P=5 MPa                  Region=?,…

Q: The dresser has a weight of 80 lb and is pushed along the floor as shown in (Figure 1). Assume h =…

A: The smallest horizontal force P, the acceleration, and the normal reactions at A and B.Given:The…

Q: Water is flowing upwards through the venture meter shown in the figure. The water volumetric flow…

A: Water flow rate, Q=77 m3/sWater specific gravity, SGw=1Mercury specific gravity, SGHg=13.54Elevation…

Q: Using your own words Discuss in details the concept of bouncy force and flotation. Discuss the…

A: Concept: Bouncy Force: The upward force which is exerted by the fluid against the weight of…

Q: PROBLEM 4: The basic barometer can be used to measure the height of a building. If the barometric…

A:

Q: 3.) Air is heated in an Isometric process where the pressure increases. It initially has a state of…

A:

Q: Obtain the equations governing the following viscoelastic models.

A: Given Data→ Viscoelastic Models.

Q: termine the minimum value of a horizontal force P applied to the lower block.

A:

Q: draw the isometric view of the drawing identify the alphabets of lines on the orthographic view

A: Find Isometric view of the object

Q: b. Compute for the gravitational force that each particle exerts on the other.

A: Q7)

Q: Chapter 12, Reserve Problem 003 The stresses shown in the figure act at a point in a stressed body.…

A: The stresses shown in the figure act at a point in a stressed body.If (stress)y = 39 MPa in the…

Q: 1. In the figure below, which of the objects (A, B, C, or D) matches the three orthographic views…

A:

Q: A beam carries loads as shown in Figure P1 below. Specify the suitable dimensions of the beam if the…

A: σlimit=18000 psi  =18000× 6895=124.11×106 N/m2sectional shape a) square b) solid circular c)…

Q: 4. Superheated steam at 18 MPa, 560°C, enters the turbine of a vapor power plant. The pressure at…

A: GIVEN :- P1=18MPaT1=560°CP2=0.06 barηturbine=82%ηpump=77% TO FIND :- (d) heat transfer to cooling…

Q: 3. Water vapor enters a turbine at p, = 4 bar, T1 = 200°C and exits at p2 = 1 bar with a quality of…

A: As you have asked for only d part so I have given solution for d only.

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.