UBI Oa. 59.6 db2₁1 mAb. 100 ΚΩb. 71.7Vec-VccOrQA15. In the circuit shown above VA = 100V and B=100 for all transistors. The output resistance, Rout, is:a. 50 ΚΩd. 200 ΚΩ16. In the circuit shown above the differential gain Ad is approximately:ReOUMc. 150 ΚΩc. 65.6dbd. 82.5db

Answered: Image /qna-images/answer/3ae4ca32-08fe-42fc-914c-870d9220729a.jpg

a. UBI O a. 59.6 db 0₂ 1 mA b. 100 ΚΩ b. 71.7 Vec -Vcc Q 15. In the circuit shown above VA = 100V and B=100 for all transistors. The output resistance, Rout, is: 50 ΚΩ d. 200 ΚΩ -0% Re OUM 16. In the circuit shown above the differential gain Ad is approximately: c. 65.6db c. 150 ΚΩ d. 82.5db

a. UBI O a. 59.6 db 0₂ 1 mA b. 100 ΚΩ b. 71.7 Vec -Vcc Q 15. In the circuit shown above VA = 100V and B=100 for all transistors. The output resistance, Rout, is: 50 ΚΩ d. 200 ΚΩ -0% Re OUM 16. In the circuit shown above the differential gain Ad is approximately: c. 65.6db c. 150 ΚΩ d. 82.5db

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

You are tasked with designing a linear amplifier using an NPN BJT for the circuit shown below. This means the transistor iv curves apply here. The voltages given are Vcc = 14 V and Vs = 1.0 V. The datasheet for the transistor says VBE (ON) = 0.7 V,VCE (SAT) = 0.2 V, and ß = 400. The design should have ic = 12 mA and VCE = 8 V. Find the resistances Rb and Rc that give the required ic and VCE. Vs H Rb M d VBE Rc VCE Vcc
9. State the relationships of the small signal hybrid- π parameters gm & rn to the transistor dc quiescent values. Draw the small signal model of the adjacent BJT amplifier circuit: Rs=0.5 KQ ww HH Cc Vcc= 10 V R₁ = • 56 ΚΩ www 3 R₂ = 12.2 kQ2 Rc=2kQ - VO RE=0.4 KQ
A-Design a two-stage BJT amplifier as shown in the figure with coupling capacitors such that the 3 dB low frequencies associated with each stage are equal to 20 Hz. The transistor parameters are: ß = 200 and 1=5.21KQ. Vcc=5V Rc1= 3.5 kQ2 SR₁ = 3.55 ΚΩ R₁ = 55 k Ri R₂ = 31 kQ2 CCI REL= C1kQ2 HH Cc₂ www Ri R₂ = 31kQ2 RE2= ΣΙΚΩ
The following amplifier (consider the case with a load) consists of a ? channel JFET. In the amplifier the value of the source DC = (+ VDD = 20V) and of all the resistors (shown in the schematic) and capacitors C1 = C2 = 20 uF is known. At the same time, the JFET has the following specifications: IDSS = 10mA and VP = -3.5V. The output resistance of the JFET is: rd=infinity Ω (infinity ohm) Determine the following, Analysis in DC a) The value of IDQ.b) The value of VDSQ.
24 3 Vsige VGG I RO RS VAP Vout Rout Consider the mosFET Circuit Shown In which &p=3-3 kuz Ac and Rs=4702. The Dc Sources VOD and VGG Set gm = 15 MATU Determine the Overall Voltage gan, Cav Determine the 2 Determine the F3 Out Put resistance Input resistance
Select a MOSFET which can be operated in both depletion and enhancement modes. E- MOSFET None of the given choices D- MOSFET as well as E - MOSFET D- MOSFET
For a common-collector amplifier, RE = 100N, r. = 10N, and 30ac = 150. If a 10 mV signal is applied to the base , the output signal is approximately 10 mV 150 mV 1.5 V 100 mV
A transistor amplifier circuit is biased so that the quiescent point is to the far left of the load line midpoint. What do you expect to occur when the input voltage begins to vary? O The output voltage will be distorted on the bottom because it will hit the lower limit for VCE before the input voltage arrives at its peak. The output voltage will be distorted on the top because it will hit the upper limit for VCE before the input voltage arrives at its peak. O The output voTransistor's output voltage will look like the input voltage amplified and inverted. The output voltage will be zero (flat).
Which of the below is not a characteristic of "biopotential amplifier": O Specfically designed to process bio-electric signal. They have a low input impedance Oc They have high CMRR Ob Od. They keep good quality of the signal leads to a high endurance electrode. Oa Blectrolytic manufacturing process Ob. All of these Oc Sintering Manufacturing process Od. None of these
2. The parameters of the transistor as shown in the figure below are ß = 100 and VA = 100V. a. Find the dc voltages at the base and emitter terminals. b. Find Rc such that VCEQ = 3.5V. c. Assuming Cc and CE act as short circuits, determine the small-signal voltage gain Av = Vo/Vs. d. Repeat part (c) if a 5000 source resistor is in series with the vs signal source. V+ = +5 V Rs = 100 £2 www Us Cc RB = 10 ΚΩ I= Iausmi 0.35 mA www RC -000 V=-5 V CE
Please solve both
ZAIN IQ lI.. A docs.google.com The emitter current is always greater than the base current O less than the collector current O None of these O All the above O O O