11. An SCR bridge takes power from a 120 VRMS 60 Hz source, and provides it to a load at a nomi- nal 72 V dc. a. What phase delay angle a will be used to meet this requirement? b. Plot the output voltage of the bridge, one of the switching functions, and the input current wave- form for your value of a from part (a), given a large output inductor and a 10 A load. c. If the output power is to be 1 kW, what value of inductance will be needed to keep the output ripple below 1% peak-to-peak?

11. An SCR bridge takes power from a 120 VRMS 60 Hz source, and provides it to a load at a nomi- nal 72 V dc. a. What phase delay angle a will be used to meet this requirement? b. Plot the output voltage of the bridge, one of the switching functions, and the input current wave- form for your value of a from part (a), given a large output inductor and a 10 A load. c. If the output power is to be 1 kW, what value of inductance will be needed to keep the output ripple below 1% peak-to-peak?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A group of UTAS-Nizwa students are working on a project entitled "Gas leak detector alarm" for their final year in Diploma level. The circuit works on DC voltage of 16 volts and DC current of 7 milliampere. Students need to design a power supply circuit for their project. Consider an RMS voltage input of 220 volt, 60 Hz. Using a Full Wave Bridge Rectifier with Transformer, Silicon diode and Capacitor Filter, Design the power supply. a. Compute for the load resistance, peak output voltage, input peak voltage to the diodes (secondary voltage), peak input voltage and the turns ratio of the transformer. 1. What is the value of the load resistance? b. Draw the Power Supply circuit (capacitor filter connected in parallel with the resistor) and write the computed values (No value for the capacitor).
I need the answer quickly
A three-phase 1MW AC-DC converter is to be connected to a 2.4kVLL/60Hz AC bus that presents a 200uH inductance per phase. What is the maximum magnitude, in Arms, that the 13th current harmonic of the converter can have, in order to comply with the IEEE 519 standard?
What is the importance of a full-wave bridge type power supply and its advantages and disadvantages?
Digital Electronics and Design Questiona) Write a 2:1 MUX module using Verilog-HDL.b) Use the module in (a) and write a Verilog-HDL code to implement a 4:1 MUX.
Draw a phase bridge type Full wave uncontrolled AC / DC converter circuit, describe the operating principle, draw input-output voltage curves, and write the integral correlation that gives the average value of the DC output voltage in any t1 instantaneous trigger state
Sketch the voltage transfer characteristics of an ideal voltage amplifier and a real voltageamplifier. Ensure to label the important regions.
Show the downward shift of the output signal with the series capacitor and diode.Clampers or DC restorers are clamp a peak of a waveform to a specific DC level comparedwith a capacitively coupled signal which swings about its average DC level (usually 0V).If the diode is removed from the clamper, it defaults to a simple coupling capacitor– noWhat is the clamp voltage? And, which peak gets clamped? Why is this so? Voltage values: Capasitor value: 1000 pFDC offset: 0 VAmplitude: 5 VFreq: 1 KHz
A basic regulator has an 8.5V zener diode of 0.5 W power and a filter voltage of 32VDC, determine the following electrical parameters: a. Calculate the minimum zener current. b. For a flexible design the diode work at 45%, what is the test current of the zener diode? c. If the load current is 10mA, what is the value of the limiting resistor connected between the zener and the filter?
a. A 220 ohms resistor is connected in series with the gate of an SCR using basic circuit in figure. The gate current required to fire the SCR is 10mA.What is the input voltage (Vin) is necessary to switch on the SCR?
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
The circuit diagram of step-up type DC-DC converter is given below. It is assumed that the output capacitor is large enough and the output voltage is constant. (Consider that there is no circuit losses.) What should the inductance value be in order for the circuit to always operate in the Intermittent Current Mode (DCM)?Calculate.