1. What is the condition for over modulation and what are its effects?2. Name the frequencies generated in the output of an Amplitude Modulator.Draw the AM waveform, if the modulating signal is a square pulse waveform4. Draw the AM waveform, if the modulating signal is a sine waveform and thepercentage modulation is 100%.

Answered: Image /qna-images/answer/99f49e3f-cdf0-42b6-92e5-03dfdaa0f9d6.jpg

Answered: 1. What is the condition for over…

Engineering

Electrical Engineering

1. What is the condition for over modulation and what are its effects?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Example 2.5.3 Find the resistance R and he for the transistor to provide a resonating frequency of 5 kHz of a transistorised phase shift oscillator. The biasing resistance are 25 1O and 47 1Q. The load resistance is 10 k2. The capacitor in the tank circuit is 1000 pF while h, of the transistor is 2 k2.
The term duty cycle refers to the amount of time a signal is complete cycle. A. off compared to the period of one B. on The output voltage of op-amp is positive saturation, when the voltage applied to the input is greater than the input. A. inverting B. noninverting A square wave that is 20V at its high state and OV when it is off will produce an average DC when its duty cycle is 75%. Formula: VOUT = Duty Cycle * Peak voltage voltage of A. 7.5V B. 10V C. 15V
For the circuit below define the fields described in the rows by matching them to a letter given for an equation or a value in Figure 1. v. () (1+ jwRC) v. () ¯(1 + J»RC) (a) (b) R Zero Infinite (c) (d) V (1+ jeRC) (f) (e) Unity (e) (h) Figure1. Output voltage in terms of input voltage Choose... + The expression for the ratio of input voltage to output voltage Choose... + as frequency tends towards zero Gain as frequency tends Choose... + towards zero Voltage Gain Choose... + Gain as frequency tends towards infinity Choose... + Choose... +
(c) Make a tabulated comparison between the three different multilevel converter topologies (i.e. cascaded H-bridge, Diode-clamped and capacitor-clamped). Use five-level single-phase converter as a base for your comparison. The comparison should highlight the advantages, disadvantages and the practical design consideration.
In the boost 1) Source voltage E value: (A B) -Voltage voltage range 2) Switching frequency value: M kHz 3) Voltage between load terminals (Vload) F (Voltage) 4) capacitance value 470 (microfarad) 5) Pload in load >= H (watts) Which, in microhenry, is the lowest inductance L that can keep the DC DC converter in continuous current under conditions of DC DC converter circuit, given below A=7V B= 19V M=25Khz F=45V H=8watt A) 521.44 B) 492.66 C) 103.44 D) 378.62 E) 258.55
Describe the signal in Figure E.49 as a ramp function minus a summation of step functions. 15 x(t) Imm 4
Choose the correct answer
For DAC with resolution of 0.16 volt and to full scale reading of 10 voltages: Design suitable Binary Weighted Resistor DAC and sketch the circuit Design R-2nR DAC and sketch the circuit Calculate the input digital signal and the related output signal at 25% intervals of the full scale voltage value. Calculate the voltage at the ladder points. Put the result fo your calculation in a i. ii. iii. iv. table.
Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the main power supply of (220 Vrms). Find: - 1- The transformer turns ratio (a). 2- The ripple voltage. Voludit) Vm = 12 V 3- The Vde value. 4- The RMS value of the output voltage. 5- The ripple factor. 6- The value of capacitor filter. = 0.1 V (assume ideal diodes) T=0.01 sec. tisec)
What are programmable amplifiers and attenuators? Give an example
Calculate the input impedance for small-signal equivalent circuit. Circuit Parameters / R1=9 k2, R2=13 kn, =20 kn Vcc R1 WナKa R2 Rin a. 26.162 ko O b. 16.879 kn O c. 10.971 kn O d. 22.786 ko O e. 29.538 kn
Electronic