a. The AC system used instead of DC system in power transmission in o possible to: 1) Reduce the risk of electric shock. 2) Reduce the cost of generating electric power. 3) Send the power to far loads. b. The reactive power is that transfer: 1) From source to load. 2) From load to source. 3) In both directions mentioned above. C. The unit of the permeability is: 1) H-¹.A. 2) H.m-¹. 3) H A-¹, 9

a. The AC system used instead of DC system in power transmission in o possible to: 1) Reduce the risk of electric shock. 2) Reduce the cost of generating electric power. 3) Send the power to far loads. b. The reactive power is that transfer: 1) From source to load. 2) From load to source. 3) In both directions mentioned above. C. The unit of the permeability is: 1) H-¹.A. 2) H.m-¹. 3) H A-¹, 9

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

Which of the following is not true for ferromagnetic materials? Please choose one: a. High?mthey have value. b.Above the Curie temperature, they lose their non-linear properties. C. a fixedµrthey have value. D.The energy loss is proportional to the area of the hysteresis loop.
What are the characteristics of an excellent DC power source? Give 3 and explain.
I need the answer at 20 minute
A triac can pass a portion of …………… half-cycle through the load a. neither positive nor negative b. both positive and negative c. only negative d. only positive
8 = 0 Q1: What does happen if we change two currents? Q2: What does happen if we have a three-phase four poles machine? a Q3: What does happen if we have a two-phase two poles machine? Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali K....p. . --
1-Choose the correct statement for pure resistor connected across single phase AC supply. a. Current and Voltage are in phase b. Current leads the supply voltage by 90° c. None of these d. Current lags the supply voltage by 90° 2-Identify the current through the inductor in a RL transient circuit connected across DC voltage, when the switch is kept open. a. 0 b. Infinity c. V/R d. 1
2. A burst controlled triac is feeding a 200 ohm resistive load. The AC supply providing 240 V rms voltage at 60Hz. a) For one cylcle on, four cycles off control calculate the load rms voltage, current, power transferred to the load and efficiency. b) For four cylcles on, one cycle off control calculate the load rms voltage, current, power transferred to the load and efficiency.
An AC circuit is shown in the diagram. The source of emf has a peak voltage of 9.00 V and a frequency of 60.0 Hz. Assume the wires contribute a negligible amount to the resistance and the AC source has negligible internal resistance. 524 2 493 2 1.56 k2 a) Find the equivalent resistance of the circuit. Redraw the circuit showing the equivalent resistor and use this simplified circuit for the rest of the problem. 315 2 Re = b) Find the rms current. 9.00 V, 60.0 Hz c) If the current is zero at time t= 0, find the first two times (after time t-0) that the current is equal to its rms value. and d) Find the average power dissipated by the circuit.
A circuit consists of an AC voltage source, a 10-ohm resistor, and a capacitor, all connected in series. The magnitude of the impedance of the capacitor is also 10 ohms. Which of the following is true about the source voltage and the current through the circuit? a. Insufficient information is given. b. The source voltage will lag the current. c. The source voltage will lead the current. d. The source voltage will be in-phase with the current.
What will happen to the value of the impedance if the resistance will be increased or decreased? Explain...
What are the elements which contribute to the cost of the electricity? And discuss how the “load curves’ and ‘load duration curves’ can helpful in the economics of generation.
In case all the flux from the current coil 1 links with coil 2, the coupling coefficient will * .be equal to ... . of its maximum value