Four masses m,=100 kg, m2=175 kg, m3=200 kg and m4=25 kg are fixed to the cranks of 20 cm radii and revolve in planes 1,2,3 and 4 respectively. The angular positions of cranks in planes 2,3 and 4 with respect in the crank in plane 1 are respectively 75°, 135° and 200° taken in ccw sense. The distances of planes 2,3 and 4 from plane 1 are 60 cm, 180 cm and 240 cm respectively. Determine the angular position and magnitude of the balanced masses at a radius of 60 cm in plane L and M located midway between planes 1 and 2 and planes 3 and 4 respectively.

Four masses m,=100 kg, m2=175 kg, m3=200 kg and m4=25 kg are fixed to the cranks of 20 cm radii and revolve in planes 1,2,3 and 4 respectively. The angular positions of cranks in planes 2,3 and 4 with respect in the crank in plane 1 are respectively 75°, 135° and 200° taken in ccw sense. The distances of planes 2,3 and 4 from plane 1 are 60 cm, 180 cm and 240 cm respectively. Determine the angular position and magnitude of the balanced masses at a radius of 60 cm in plane L and M located midway between planes 1 and 2 and planes 3 and 4 respectively.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question.
i need the answer quickly
3. Which of the following statements about the use of structural steel as an equipment grounding conductor(EGC) in an AC system is correct?A. Structural steel isn't allowed for use as an EGC.B. Structural steel can be used as an EGC bonding jumper between panelboards.C. Structural steel must have an EGC bonding jumper every three feet of structure.D. Structural steel can be used as an EGC when it's bonded at both ends.
We are running 3 wires and a ground in a RMC to a control panel with a 60 amp circuit breaker disconnect in the control panel. The conduit is run along the ceiling where the ambient air temperature is 100 degrees. The control panel feeds our secondary cooling pump. What size are the ungrounded conductors? All conductors have typeTHHN insulation. A #6 AWG B 600 Kcmil C #8 AWG D #2 AWG What size RMC do we need? A 3" B 3/4" C 1" D 1 1/2"
Estimate the length of conduit to perform the next bends. EMT will be bend using a hand bender. Provide your answer in inches (just the number) using up to 2 decimals. The picture shows two panels connected by a back-to-back 23.5" stubs EMT 3/4" 6.25 ft P
A seven-segment display is a device composed of 7 elements, as shown in the figure below. Each element is selectively lit to form patterns such as numbers or letters. For example, to display '0', the segments A, B, C, D, E and F have to be simultaneously lit. A circuit decoder takes in a 4-bit binary number and produces the outputs A, B, C, D, E, F and G. The outputs of the decoder are then fed to the seven-segment display as shown in the figure. The seven-segment display should show the sum of the 4-bit input + 1. For example, if the 4-bit input is 000 , the decoder’s output will lit up the seven-segment display that will show the numerical number 1. This corresponds to the decoder output of 01100002. In the case wherein the 4-bit input = 1001 , the decoder’s output will lit up the seven-segment display that will show the numerical number 0. This corresponds to the decoder output of 1111110 . The decoder’s output line should be logic “1” if the segment will be lit and “0” otherwise.…
What is RG rating of coaxial cable. Please give me detailed information. Don't copy previously given Answer
When using an oscilloscope for testing engine management systems, what is an attenuator used for? In your answer provide an example of when an attenuator should be used. (5 - 10 words)
4. Do some search about the functionality of Airport Metal Detectors. Explain your answer in a paragraph.
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
I need the answer as soon as possible
Please, I need the final solution as soon as possible, I do not need any explanation or explanation