A. The 370 N force acting on the frame as shown in figure is to be resolved into two components acting along the axis of the AB and AC. If the component of force along AC is required to be 600 N. directed from A to C, determine the angle O between AB and AC. 370 N

Q: The bar is supported by a roller constraint at B, which allows vertical displacement but resists…

A:

Q: Q3. The 500 N force acting on the frame is to be resolved into two components acting along the axis…

A: For a body to be in equilibrium follows conditions must be fulfilled: Sum of all the forces in the…

Q: The 39N force P is applied perpendicular to the portion BC of the bent bar as shown in Figure 1. a)…

A:

Q: Determine the resultant moment produced by force P= 170N about point O, in Nm. Set α= 35-degree

A: P=170N To find moment about point O

Q: The boom AC in the figure rests in a ball and socket joint at A and is held in equilibrium by the…

A: To find: Coordinates of D

Q: Consider the foliowing free body dagram 2 N/m 20 m 10 m A- 20 N B,- 20N 20-x 2N/m A- 20 N 50 N/m 200…

A:

Q: A vertical shaft AB is 6ft long and bolted to a rigid support T ITS LOWER END.. At its upper end B…

A:

Q: The deflection curve for a simple beam AB (see figure) is given by the following equation:   A.…

A: ##using deflection curve equation CALCULATIONS of Loading,  Reaction,  And BM ##

Q: Force F acts at polnt C on the bent plpe OABC. 50° 5.60 ft 3.20 ft 40° F= (-4.6i - aj + 4.5k) kips…

A: The given figure is shown below:

Q: F₁=250 N 300 A -2 r -3 m F₂ = 300 N 60° 4'm F3 = 500 N

A:

Q: 2. Determine the reactions at the supports A, B, and C, then draw the shear and moment diagrams. El…

A:

Q: A 599-N force is applied at A as shown. y = 469 mm. Determine (a) the moment of the 599-N force…

A: Given data  P = 599 N  y = 469 mm  Find moment about D (counterclockwise taken as positive).

Q: y | 1 A -X 25' 15⁰ 40° C F = 13 kips 15' B 11 .n

A:

Q: 4. DETERMINE THE MOMENT OF THE FORCE F AT THE END OF THE ANGLE BRACKET ABOUT POINT O. THE VALUE OF F…

A:

Q: 12. Two forces can be replaced by an aquivalent force R acting at point B on the beam. Determine the…

A: Hi there! since you have asked multiple questions, we will solve the first question for you. If you…

Q: The -KN force F is applied at point A (a) Compute the moment of F about point O, expressing it both…

A: F→=- 3.7×932+92 i^ - 3.7×332+92j^         =  -3.51⏜-1.17j⏜ kn r→=0.9,1.6  = 0.9i⏜+1.6j^ m τ→=r→×F→…

Q: Replace the force system by an (a) equivalent resultant force and (b) couple  moment at O. Take F3 =…

A: Given:From the figure:F1=-300kF2=200jF3=-0.15i-0.2j+0.3kNow,Equivalent resultant force is given…

Q: в P. A 60

A:

Q: 4-The force F = 450 lb acts on the frame. Resolve this force into components acting along members AB…

A: In this question a frame is given Load equal to 450 LP is applied on joint a We are asked to find…

Q: Determine the force in each bar of the truss shown in the figure in terms of P.

A:

Q: A 867-N force is applied at A as shown. y = 478 mm. Determine (a) the moment of the 867-N force…

A:

Q: 160 mm 480 N 60 mm 80 mm CD = Cx = -795N, left E 150 mm 60 mm 100 mm B.

A:

Q: 100 N 100 N IN 1 DETERMINE THE MOMENTO OF THE TWO FORCES ABOUT X Y. AND ZAES BHOWN IN THE FOURE

A:

Q: Solve for the moment about A (in N-mm) of the coplanar-noncurrent forces shown below. Use mm as the…

A:

Q: If force f = 600N, determine the components of the forces at B, C and D. Draw the FBD of each member…

A: Given: The value of force F is 600 N. Consider the figure,

Q: Replace the three forces shown by an equivalent force-couple system at point A. If the forces are…

A:

Q: Solve the resultant of the given concurrent forces.Given angle = 30 degrees

A: From the given question it is required to determine the resultant of the given concurrent forces.

Q: a. The reaction at the roller support in kN. b. The deflection at point "B" in terms of El.

A:

Q: 24KN/m 12KN/m Зт A simply supported beam is loaded as shown in the figure. Assume El is constant.…

A:

Q: For the beam in figure 9, whose dimensions are in meters, determine the reactions at supports A and…

A: Determine the support reaction at A and E.

Q: Determine the vertical reaction (in kN) at the support C of the given beam using Method of…

A: Given data in question  Load P Span member length  To find out  Reaction C

Q: 1. Determine the Moment due to force F about: a. Point O b. Point B Note: The thickness of the beam…

A: To Determine The Moment due to force F about: a. Point O b. Point B

Q: If the force F = 100 N lies in the plane DBEC, which is parallel to the x–z plane, and makes an…

A: Lets first find out position vectors for points A and B,

Q: A beam with a Z cross-section is subjected to a moment M, which has a magnitude of 20 kip - in. The…

A:

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.