The Dynaco Manufacturing Company produces a product in a process consisting of operations of fivemachines. The probability distribution of the number of machines that will break down in a week follows:Machine BreakdownsProbabilityper Week0.10.220.10.250.30.05a. Simulate the machine breakdowns per week for 20 weeks.4.b. Compute the average number of machines that will break down per weck.

Machine breakdown is when the specified machine does not work at all or does not operate in the…

Answered: a. Simulate the machine breakdowns per…

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

Operations management is the process of creating a set of specifications from which the product can be produced;True or False
Is the basic standard approach best to mitigate against operational risk where human error is concerned? and why?
snip
It takes Carissa 45 minutes to finish a 60-ietm test in math. At this rate, how many minutes will it take her to finish a 120-item test?
Secretaries are failing in terms of filling, by doing proper and accurate filling in the work place. Discuss the cause of the failure.
Smooth Chin Device Company The Smooth Chin Device Company is a manufacturer of high--end electric razors. These razors are produced using a machine--paced process. For each razor, a tray with components enters the process at the beginning of a conveyor belt. The tray then passes through the six steps (consisting of various tasks) explained in the table below. Workers perform the assembly operations on the moving tray. The last step consists of an inspection of the then fully assembled razor. The activity times of the process are as follows: Station Tasks A Preparation 1. Lay out chassis [12 sec] 2. Lay out screws [15 sec] 3. Lay out all other components [17 sec] Total time for A: 44 sec B Assembly 4. Perform task AS1 [10 sec] 5. Perform task AS2 [10 sec] 6. Perform task AS3 [20 sec] Total time for B: 40 sec C Assembly 7. Perform task AS4 [14 sec] 8. Perform task AS5 [16 sec] 9. Perform task AS6 [20 sec] 10. Perform task AS7 [5 sec] Total time for C: 55 sec…
These four phases make up a machine cycle, which is also known as a process loop. What percentage of a machine's cycle time do you value the most? Should I be concerned about replacing parts of the machine cycle when they wear out? Does the implementation of a second module resolve the problem of toggling between them?
Plz do fast asap
These four phases make up a machine cycle, which is also known as a process loop. What percentage of a machine's cycle time do you value the most? Should I be concerned about replacing parts of the machine cycle when they wear out? Is the problem of switching modules improved by adding a second module?
Line X has 2 identical machines(inspection#1 and #2) that each process 420 parts per hour. Both machines run for 3.5 hours before inspection #1 is shut down for a change over. That change-over takes 40 minutes. Inspection #2 needs a changeover that takes 1 hour. How many parts are produced in 8 hours?
A fleet repair center resets its computerized diagnostic system after every 15 trucks to help ensure there are limited major downtimes from system failure. The reset takes 22 minutes on average with a CV of 0.3. Each trucks diagnosis takes 28 minutes on average with a CV of 1.75 not considering the resets. 1. What is the effective process time and its CV? 2. If the reset system is not used, failures will occur after 57 hours on average with an average repair time of 3 hours. The CV of repair time is 0.9. What is the effective process time and its CV? Is the maintenance system beneficial if it prevents breakdowns? Just consider effective processing time parameters. 3. The maintenance program costs $10,000 annually. The average profit per car from the diagnostic service is $75. Assume the service center operates 250 days per year, 10 hours per day. Is the maintenance program economically beneficial? What assumptions are needed?
Please elaborate on your response. In gratitude The firm will no longer provide support for your present LIS system, thus you will need to choose a new one. In order to choose the optimal setup for your lab. (Remember that throughout this transition, you must maintain testing on the present system.) How and why do you handle all divisions simultaneously?

SEE MORE QUESTIONS

Recommended textbooks for you

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Business in Action

Operations Management

ISBN:

9780135198100

Author:

BOVEE

Publisher:

PEARSON CO

Purchasing and Supply Chain Management

Operations Management

ISBN:

9781285869681

Author:

Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson

Publisher:

Cengage Learning

Production and Operations Analysis, Seventh Editi…

Operations Management

ISBN:

9781478623069

Author:

Steven Nahmias, Tava Lennon Olsen

Publisher:

Waveland Press, Inc.

SEE MORE TEXTBOOKS

a. Simulate the machine breakdowns per week for 20 weeks, b. Compute the average number of machines that will break down per week.