A process with five steps has a cycle time of 1.5 minutes per unit. The only inventory in the system is held before the last station, where 35 units of inventory are maintained. A defective unit is produced at the first station but is not detected until final inspection (after the fifth station). Round your answer to one decimal place. What is the information turnaround time (in minutes)? minutes

A process with five steps has a cycle time of 1.5 minutes per unit. The only inventory in the system is held before the last station, where 35 units of inventory are maintained. A defective unit is produced at the first station but is not detected until final inspection (after the fifth station). Round your answer to one decimal place. What is the information turnaround time (in minutes)? minutes

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

Inspection time 0.5 days Wait time (from order to start of production) 15.7 days Process time 2.6 days Move time 0.6 days Queue time 3.5 days If by using Lean Production all queue time during production is eliminated, what will be the new MCE? (Round your percentage answer to 1 decimal place.) New manufacturing cycle effciency ?
Please do not give solution in image format thanku
Please do not give solution in image format thanku e) Data collected from the Rapid Jet's check-in counter indicated that 160 passengers checked in between 2pm and 3pmf for a flight departing at 3:30pm. A group tasked with making the process more efficient noticed that the average number of passengers waiting to check in was 20. How long was the average passenger waiting in line?
Usually, it takes days to offer a service in e.government. Select one: a. True b. False
A 10 station automated assembly system produces an ideal cycle time (Tc) of 14 seconds/cycle. When a defective part enters any assembly station it sometimes causes a station jam or stoppage. Defective parts occur at a rate of 0.07 and a jams due to defective parts occur at a rate of 0.4. When a jam occurs, it takes on average 74 seconds to clear and restart the station. Determine the production rate of acceptable parts (Rap) to the nearest 1 part/hour.
Navern Corporation manufactures and sells custom home elevators. From the time an order is placed until the time the elevator is installed in the customer's home averages 141 days. The 141 days are spent as follows: Wait time Inspection time Process time Move time Queue time What is Navern's manufacturing cycle efficiency (MCE) for its elevators? Multiple Choice O O 41.1% 30.4% 58.9% 29 days 24 days 34 days 31 days 23 days 57.4%
12
Answer is complete but not entirely correct. A campus deli serves 300 customers over its busy lunch period from 11:30 am to 1:30 pm. A quick count of the number of customers waiting in line and being served by the sandwich makers shows that an average of 7 customers are in process at any point in time. What is the average amount of time that a customer spends in process? Instruction: Round your intermediate and final answer to 1 decimal place. Average amount of time (Round to one decimal) 4.9 8 minutes
A new customer walks into SLC Barber Shop every 60 minutes on average, with a standard deviation of the interarrival times being 60 minutes. At SLC Barber Shop, the average service time is 30 minutes, with a standard deviation of service times being 45 minutes. 1. What is the utilization of the barber? 2. What is the CVa? 3. What is the CVp?
Among the tools of TOM, the tool ordinarily used to aid in understanding the sequence of events through which a product travels is a: Pareto chart flowchart check sheet Taguchi map poka-yoke
Explain what makes the interactive model different from the waterfall model when it comes to maintenance operations.
Hammond Inc. has analyzed the setup time on its computer-controlled lathe. The setup requires changing the type of fixture that holds a part. The average setup time has been 135 minutes, consisting of the following steps: Step Time (in minutes) Turn off machine and remove fixture from lathe 13 Go to tool room with fixture 15 Record replacement of fixture to tool room 18 Return to lathe 20 Clean lathe 17 Return to tool room 20 Record withdrawal of new fixture from tool room 12 Return to lathe 15 Install new fixture and turn on machine 8 Total setup time 138 Why should management be concerned about improving setup time? What do you recommend to Hammond Inc. for improving setup time? How much time would be required for a setup, using your suggestion in (b)?