A. Select the correct answer 1. Which gear train is used for higher velocity ratios in a small space? a- Reverted gear train c- compound gear train 2- Which type of gear train is used in clock mechanism to join hour hand and minute hand? a- Reverted gear train c- compound gear train 3- Which type of gearing is used in steering system of an automobile? a- Rack and pinion c- Spiral gears b- Simple gear train d. Epicyclical gear train b- Simple gear train d- Epicyclical gear train b- Worm and wheel d- None of the above 1. The tyne of goarS used te connect twe non parallel and non intersecting shafts is

A. Select the correct answer 1. Which gear train is used for higher velocity ratios in a small space? a- Reverted gear train c- compound gear train 2- Which type of gear train is used in clock mechanism to join hour hand and minute hand? a- Reverted gear train c- compound gear train 3- Which type of gearing is used in steering system of an automobile? a- Rack and pinion c- Spiral gears b- Simple gear train d. Epicyclical gear train b- Simple gear train d- Epicyclical gear train b- Worm and wheel d- None of the above 1. The tyne of goarS used te connect twe non parallel and non intersecting shafts is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

what occurs in a differential during cornering? a. the inside axle side gear turns faster than the outer axle side gear b the case turns at the same speed as the drive shaft c the crown gear will slow down slightly d the pinion/spider gears rotate on the pinion shaft
Part 2: Gears www w The smaller gear wheel is connected to an electric motor, while the larger gear is connected to a turning platform. 1. Which gear is the 'drive gear' and which is the 'driven gear'? 2. Calculate the gear ratio by counting the teeth on each gear wheel. 3. Calculate the gear ratio by measuring the diameter on each gear wheel. 4. If the drive gear rotates clockwise, which way will the driven gear turn? 5. If the drive gear rotates at 60 RPM, what is the rotation rate of the driven gear? 6. If the drive gear generates 1 Nm (torque), what is the torque of the driven gear?
For o, = 60 rpm clockwise (CY) when looked from the left, what is the angular velocity of the carrier and its direction so that Gear 4 rotates in counter clockwise (CCW) directi on at twice the angular velocity of Gear 1 when looked from the left?
The gear train used in automobile differential is a. simple gear train. b. compound gear train. c. epicyclic gear train. d. both answers (a) & (b).
Question Comple Which type of gear is depicted in the figure below?
1.Single Choice Problems 1) The following method A. Increase the small pulley diameter C. Increase the big pulley diameter and reduce the center distance can be used to increase the small pulley angle of belt drive. B. Reduce the small pulley diameter 2)Belt drive under normal operating conditions, the phenomenon that exists between belt and pulley is A. Slipping С. Creeping D. Slipping and creeping B. Exactly the same speed 3) A pair of meshing gear drive, the pinion material is 40Cr, the gear material is Number 45 steel, so the contact stress at the engagement. A. O HI D. Not sure Β. σΗι C.O HI >OH2 : Ở H2
Q12:- The figure below shows an epicyclic gear train. Pinion A has 15 teeth and is rigidly fixed to the motor shaft. The wheel B has 20 teeth and gears with A and also with the annular fixed wheel D. Pinion C has 15 teeth and is integral with wheel B (B and C being a compound gear wheel ). Gear C meshes with the annular wheel E, which is keyed to the machine shaft. The arm rotates about the same shaft on which A is fixed and carries the compound wheel B,C. If the motor runs at 1000 rpm, find the speed of the machine shaft. Also find the torque exerted on the machine shaft, if the motor develops a torque of 10 kg.m.
Identify label B in the following spur gear diagram. Tooth thickness Width of space Pitch circle H. Bottom land Fillet radius F- Select one: O a. Addendum Circle b. Involute Circle O c. Base Circle d. None of these options e. Dedendum Circle O f.Dedendum Type here to search Face width Top land B.
1- What is the benefit of the epicyclic gear train? Name some applications? 2- Why does efficiency increase with increasing load? What is the reason for the difference between practical and theoretical efficiency? 3- What is the function of the epicyclic system in the car when turning?
2. When inspecting a transaxle's gears, be Technician A says that a shiny wear pattern on the center of the gear teeth is normal. Technician B says that it is normal for a reverse idler gear to have small chips on its engagement side. Who is correct? A. A only C. Both A and B В. В only D. Neither A nor B
The advantage of the helical gear drive over the spur gear drive is 1) teeth failure can be controlled 2) ease to manufacturé 3) the contact area is less during meshing 4) the contact area is more during meshing
Two spur gears are engaged with the angles of approach and recess as 23° and 17° respectively. What is the con- tact ratio if the pitch angle is 27°?