The smaller gear wheel is connected to an electric motor, while the larger gear is connected to a turning platform. 1. Which gear is the 'drive gear' and which is the 'driven gear'? 2. Calculate the gear ratio by counting the teeth on each gear wheel. 3. Calculate the gear ratio by measuring the diameter on each gear wheel. 4. If the drive gear rotates clockwise, which way will the driven gear turn? 5. If the drive gear rotates at 60 RPM, what is the rotation rate of the driven gear? 6. If the drive gear generates 1 Nm (torque), what is the torque of the driven gear?

The smaller gear wheel is connected to an electric motor, while the larger gear is connected to a turning platform. 1. Which gear is the 'drive gear' and which is the 'driven gear'? 2. Calculate the gear ratio by counting the teeth on each gear wheel. 3. Calculate the gear ratio by measuring the diameter on each gear wheel. 4. If the drive gear rotates clockwise, which way will the driven gear turn? 5. If the drive gear rotates at 60 RPM, what is the rotation rate of the driven gear? 6. If the drive gear generates 1 Nm (torque), what is the torque of the driven gear?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is the minimum clearance allowed for meshing spur gears with diametral pitch of 20? The spur gear has 25 teeth.
Please Handwritten - Clear and organized - Mention Question # and Highlight Final answer- PLEASE ANSWER ALL 2 QUESTIONS - THANK YOU
4- Find the gearing ratio for the given compound gears shown in figure 10. 5- Given that the torque (t) of the driver gear is (40+x) N.m, find the torque of the green gear. (x is the last digit of your ID) (M) rrrrv Figure 10 Figure 11 D Error
The advantage of the helical gear drive over the spur gear drive is 1) teeth failure can be controlled 2) ease to manufacturé 3) the contact area is less during meshing 4) the contact area is more during meshing
I will rate helpful. Thank you.
A spur gear set is cut with a hob. The spur gears have a pressure angle of 20 degrees and a diametral pitch of 16 teeth/inch. The pinion has 32 teeth while the gear has 80. The customer wants to replace the spur gear set with a custom helical gear set. The only requirements are: (1) the same hob must be used (2) the gear set center distance must remain the same (3) the gear ratio must remain the same. The designer has decided to use a helical pinion with 28 teeth. For the helical gear set, select the proper helix angle that will guarantee the three requirements. Report your answer in degrees, 3 decimal places.
SYSTEM AND CONTROL (MECHANICAL) (SA2) Gear B and C are mounted on a central shaft and they rotate at the same speed/as a unit. Gear A is the driver and gear D is driven. Driver Gear (10 Teeth) Driven Gear (50 Teeth) Queshions If gear A rotates in a clockwise direction, to which direction will gear C rotates? 1 (2) .2 If gear B rotates in an anti-clockwise direction, to which direction will gear C rotates (2) 3 Calculate the gear ration of the system (6) .4 Draw the systems diagram of the above mechanism (6) [16]
The advantage of herringbone gear compared to a helical gear is the internal cancellation of its axial thrust loads Select one: True False
4. What is the overall gear ratio for the following compound gear train? What is the output shaft speed and direction if the input shaft rotates clockwise at 1000 rpm? 8 teeth, Ø 5mm 16 teeth, Ø 10mm 24 teeth, Ø 15mm 32 teeth, Ø 20mm driver driven
only hand written otherwise i'll downvote
the minimum required length of a key for a gear carrying 20,000 lb-in of torque if it mounted on a 3.75 inch diameter shaft is? (Use SAE 1018 as the key material)