a. Pulse Code Modulation (PCM) is one of the methods used in the process of converting analog signal to digital signal 3- step method (sampling, quantizing, and coding). Assuming we have a sinusoidal signal with values ranging from -2V to +2V. i. Calculate the number of bits required to represent a sample of the signal if the resulting quantization signal is to have a maximum step size, NV of 0.125V. ii. Calculate the Signal-to-Noise Ratio, SNRq due to the quantization process. iii. Explain the advantage of using non-uniform quantization.

a. Pulse Code Modulation (PCM) is one of the methods used in the process of converting analog signal to digital signal 3- step method (sampling, quantizing, and coding). Assuming we have a sinusoidal signal with values ranging from -2V to +2V. i. Calculate the number of bits required to represent a sample of the signal if the resulting quantization signal is to have a maximum step size, NV of 0.125V. ii. Calculate the Signal-to-Noise Ratio, SNRq due to the quantization process. iii. Explain the advantage of using non-uniform quantization.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Electrical Engineering _ Energy Conversion Systems pls find the question by using computer line. pls find fast.
Q2) What is Grounding.? And Why Ground.?
TII 8.) 4 – 3 kW, 230 V and 3 – 8.5 kW, 230 V clothes dryers are to be placed in a building, the total VA loading to be used for these in the computation for service entrance conductor is: A. 24375 B. 37500 C. 33750 D. 36000
Please show how to calculate the loads, give the size of wire and circuit breaker size per stall and for feeder with the given values in the table. Assume its only 1-phase, and there is no given of p.f., and the country should be based on is Philippines. Upvote will be given for sure in the end. Thank you so much! Just want to learn how does the Schedule of Load works.
Compared to the original circuit that it replaces, an equivalent circuit will always have:a. the same power dissipation.b. the same number of componentsc. the same voltage and current for a specific loadd. all of the above
Discuss and explain what is Voltage Multiplier?
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
A PMMC instrument has internal resistance of 0.8 kΩ and gives full scale deflection for 33 mA. The required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage range 75 V will be __________________ ohms. a. 226.47 b. -360.00 c. 1472.73 d. 93717.00
Question 79 Explain what are the positives and negatives of each of the controllers below: a) Proportional controller b) Integrative controlador c) Controller-proportional-integrative-derivative
16. The total voltage in a series-parallel circuit is __________ equal to the sum of the voltage drops across each resistor in the circuit. distributed across each branch in the circuit. determined by the product-over-sum method. equal to the voltage drop of the parallel branch. Which of the following statement is true both for a series and a parallel DC circuit? powers are additive voltages are additive currents are additive elements have individual currents Electric power is the ________ same as electric pressure. total number of electrons flowing in a circuit. number of electrons passing a given point in one second. rate of using or producing electric energy. A battery produces a current of 0.6 A when the external resistance is 2 ? and 0.2 A when the external resistance is 12 ?. Find the emf of the battery 3 V 6 V 9 V 12 V