a. Given re = 10 2, beta is 200, Ay = -160, and Aj = 19 for the network below, determine RC. RF, and VC- %3D Vcc RC RF = 102 B= 200 .= 80 k2

Q: "It is desirable for the following circuit, assuming the transistors are th same." A) Common fashion…

A: The given circuit is a differential amplifier circuit using transistors. (D) The CMRR (Common Mode…

Q: Vout, maxis the maximum analog voltage that you can observe at the output of the DAC. (an-1.a0)2 2n…

A: The solution is given below

Q: Q3: Answer the following A/ What is the operation amplifier application withdrawing (only five)? B/…

A:

Q: A- what information can be obtained from the open-circuit test.

A:

Q: Given: 6 = 100 -6V {200N Find: a) Ays: Vo Vs Vo B. b) Ais= io is io 400N ac vollage @ each pt.…

A: GIVEN:   β=100 FIND: (a) AVS=V0VS          (b) Ais=i0is         (c) AC voltage at each point

Q: Design a 4-bit DAC assuming high voltage of 3.5 V and a Vcc of 12 V? determine the output voltage…

A:

Q: Find for the given npn BJT circuit: Ip, Ic, lg. VCB, B VBE = 0.7V VCC = 8V R 470n R 8 V Vec 4.7 kn…

A: so we will apply kcl to find the required voltage and current.

Q: Q3) Prove that the high frequency gain for BJT is represented be equation below Ap %3D

A:

Q: Find Vc, Ve, Ieq,

A: The required parameters can be calculated by using the DC analysis of the common base amplifier…

Q: a) iii) valuer Po and Prot to choonk output voitage rang -> Nreb 三No Vve Same Ra and Rveh valua ave…

A:

Q: Q3:Answer all following branches : a) Draw (block circuit diagram) and (pins Circuit diagram) for an…

A: a)An operational amplifier is used to perform different mathematical operations like addition and…

Q: (IV) The figure below shows an R-2R ĎÁČ circuit 2R 2R 2R 2R 2R LR 2R 2R 2R Vour The reference…

A: A Digital-to-Analog Converter (DAC) is a device that converts digital signals into analogue signals.…

Q: The gate bias voltage is chosen to be VGG = 4 V and the drain bias voltage is chosen to be Vpp = 20…

A: According to the question, for the given NMOS circuit as shown below The DC load line for the above…

Q: Draw small signal equivalent circuit and derive expression of voltage gain RD R Vo Cc R2 Rs -5 V ww…

A: MOSFET(Metal Oxide Semiconductor  field effect Transistor) is three terminal electronic device.…

Q: A differential amplifier has a common mode gain of 0.2 and CMMR = 80dB. The differential mode gain…

A:

Q: Solve it correctly

A: a) Let the base current be ib

Q: 2. A 12 phase balanced midpoint rectifier provides 200A at 200V to the load resistance. The load and…

A: A 12 phase balanced midpoint rectifier provides 2 at  to the load resistance.The load and filter…

Q: 2. Using the following parameters for a Fixed - Bias JFET Circuit: VDD = +14 V, RD = 1.6 KQ, RG = 1…

A:

Q: 1. Speakers with up to 1W output(load resistance 8ohms) 2.The operating frequency range is 20Hz to…

A: Step 1: Step 2: Step 3:

Q: 10. An amplifier with an input resistance of 1000 2 is operating over a 4 MHz bandwidth. Calculate…

A: here we have to find the rms noise voltage and noise current and open circuit noise current.

Q: None

A: To perform small signal analysis for the given circuit, let's denote the transconductance of the…

Q: Sketch the output voltage of the given circuit below.

A: Given circuit and input voltages are -

Q: Q1. An audio-signal source can be represented by a 10-mV (rms) voltage source with 500-2 resistance.…

A: Given data: Voltage source VS=10-mVRS=500ΩRL=10Ω

Q: In all of the circuits, the voltage of the Vin input signal is 200mVp and the frequency is 1KHz.…

A: We have given the following diagram In all of the circuits, the voltage of the Vin input signal is…

Q: Compare the performance merits of DELTA-SIGMA, SUCCESSIVE APPROXIMATION and FLASH analogue-to-…

A: Given: Compare the performance merits of DELTA-SIGMA, SUCCESSIVE APPROXIMATION and FLASH…

Q: For a set of resistor measurement, the standard deviation found equal to ± 1.7, the the variance is…

A: In this question we need to find a variance for a set of resistor measurement.

Q: Up-down counter counts as (0. 2, 3, 6, 4, 0, ...).

A: Up-down counter counts as (0, 2, 3, 6, 4, 0 ......) Let us design this counter using D flipflops.…

Q: Q1. The output characteristic of a typical transistor is shown below, where the quiescent point is…

A: Given data, β=100VBE=0.7 V Given figure,

Q: A circuit is built around a bi-polar NPN transisor. The base network has a diode and a capacitor in…

A: Part (2) of the question is complex to answer on the platform at the moment. hence we shall help you…

Q: VDD J Vb1M3 VinM₂ Vb2M₁ = (e) Vout

A:

Q: 1. For the circuit shown in figure below use a current mesh analyzer to determine the value of the…

A:

Q: Discuss the process on how n-p-n BJT works?

A:

Q: Question 1 One of the main international societies in Electronics Engineering Select one: O a. O b.…

A: Answer (1 )correct option is (c)  IEEE (Institute of Electrical and Electronics Engineers)  beacuse…

Q: Given zener voltage at 9V, input voltage at 12Vdc to 15Vdc and ILmax at 40mA. What is Rsmin if Izmax…

A:

Q: A Thermister has 6500​​​​​​​oc resistance at 20oC, and its sensitivity is -7.2%/oC. Design a…

A: At , resistance is Sensitivity, Final temperature Power dissipation, Supply voltage

Q: Give sample system of the following systems and explain them: linear system and nonlinear system.

A: The superposition theorem's concept comprises two key features, which are described…

BJT (Bipolar Junction Transistor)

A BJT is a semiconductor device with 3 terminals that consist of a p-n junction diode that can amplify the signal or current. It is a current-controlled device. The three BJT terminals are base, collector, and emitter. The BJT works with the charge carrier, the two type of carriers in the BJT are holes and electrons, the charge carriers flow by the process of recombination. The signal to be amplifier is generally given as the input at the base terminal and an amplified form of it is available at the collector terminal.