Please answer the questions on the figure! Experiment 11. Arrange a series of experiments in Figure below on the Multisim software.... ....Ext TXFG1D21N4148R110kOvi=5V2. Connect a sinusoidal signal 10 V pp 1 kHz to the input terminal.3. Measure the shape of the output signal through the oscilloscope and document it.PPQuestions for experiment 1.Draw the input and output signals obtained in the experiment 1b. What is the value of the input signal voltage that causes the diode to change from a connected state (ON, forwardbias) to a disconnected (OFF, reverse bias)? Describe the circuit conditions under these circumstances!What is the value of the input signal voltage that causes the diode to change from disconnected to connected?а.c.Describe the circuit conditions under these circumstances!d. Theoretically, calculate and determine the resulting output voltage! Use all possible assumptionse. Compare the results from point d with point a. Is there a difference between the data and the calculated value?Describe the things that might cause this difference! Experiment 21.Arrange a series of experiments in Figure below on the Multisim softwareXsci:::: ::XPG1E COMED2IN4148R1$10ko2. Connect a sinusoidal signal 10 V1 kHz to the input terminalpp3. Measure the shape of the output signal through the oscilloscope and document itQuestions for experiment 2.Draw the input and output signals obtained in the experiment 2b. What is the value of the input signal voltage that causes the diode to change from a connected state to aа.disconnected state? Describe the circuit conditions under these circumstances!с.What is the value of the input signal voltage that causes the diode to change from disconnected to connected?Describe the circuit conditions under these circumstances!d. Theoretically, calculate and determine the resulting output voltage! Use all possible assumptionse. Compare the results from point d with point a. Is there a difference between the data and the calculated value?Describe the things that might cause this difference!

Dear student as per our guidelines we are supposed to solve only one question in which it should…

a. Draw the input and output signals obtained in the experiment 1 b. What is the value of the input signal voltage that causes the diode to change from a connected state (ON, forward bias) to a disconnected (OFF, reverse bias)? Describe the circuit conditions under these circumstances! c. What is the value of the input signal voltage that causes the diode to change from disconnected to connected? Describe the circuit conditions under these circumstances!

a. Draw the input and output signals obtained in the experiment 1 b. What is the value of the input signal voltage that causes the diode to change from a connected state (ON, forward bias) to a disconnected (OFF, reverse bias)? Describe the circuit conditions under these circumstances! c. What is the value of the input signal voltage that causes the diode to change from disconnected to connected? Describe the circuit conditions under these circumstances!

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The voltage drop is as we proceed from the supply end to the consumer points
B7
I need the answer as soon as possible
With a reference
Depending on voltmeter/ammeter terminal connection to the components, you might find different signed voltage and currents values for the same component. This causes different signed power values for the same components therefore we cannot state whether components generate or absorb power. What is your solution to this chaos? **please type it using keyboard NOT handwriting**
I need the answer quickly
Please answer in typing format please ASAP for the like Please answer in typing format please ASAP for the y
I need answer within 5 minutes please please with my best wishes
identify any equiptment at home that undergo an electromechanical energy conversion. name and discribe the function of each part involved in the conversion of the specific equiptment. with picture labeled
An AC ammeter has a direct reading 0-600A scale when used with a 400:3 ratio current transformer. The ammeter is now used with a 1,000:3 ratio current transformer. What should be the ammeter reading when the actual current is 3 A. use four decimal places if necessary.
Instructions: In Order to answer. the second picture is the guide to follow. please provide detailed step by step solution.