a. Determine the plastic section modulus. b. Determine the plastic moment capacity if Fy = 345 MPa c. Determine the uniformly distributed load it can carry.

Q: Draw the projections (Top, Front, Side) with Dimensions for this objects

A:

Q: x; ]] a» a» dz || X2 a3 a a33

A: For calculation assume,

Q: Sketch SFD and BMD in terms of w and P

A:

Q: 5. Find diameter y. All dimensions are in millimeters. 1 + 19.30 DIA 118.00 -३०

A: Tapered beam with larger diameter at AB = 19.3 mm  Length of beam ,L = 118 mm  Tapered angle = 3°…

Q: What do you mean by the slice action and how many slice operated dimensions are used?

A: #1What do you meant by the slice action?? A slice operation is defined as the particular filtration…

Q: F & H are incorrect

A: As per question requirment we only find out f and h here. Find out -  (f) Length of Curve (h)…

Q: FIHD THe CENTROID (x $ Y) of THe GazOMETRY

A: Centroid is the point where the mass of whole body acts. If there is a figure which consists of…

Q: 6 in Gin Gin 9 in 3in

A: Schematic diagram of the given problem:

Q: For the given structures, determine the degree of indeterminacy. 8. 8

A: Solution : The number of external reactions ( r ) = 9  The number of members ( n ) = 2  These values…

Q: 7⁄8 inch+  5⁄32 inch

A:

Q: Give real life examples of Mohr's Circle

A: Brief concept introduction- Mohr's Circle- It gives the relationship between the normal and shear…

Q: 1⁄6 yard +3⁄8 yard

A:

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

A:

Q: continue the last part

A: Data for pump performance curve is given. We need to select which pump combination would work for…

Q: Is sigma xy horizontal and sigma xz vertical

A: Reference: wikimedia commons

Q: 05 Find the XT 0.5 1.5 3 2.5

A:

Q: a) top most, hef tmost

A: X = 1.5 cm Y = 5.48 cm

Q: hat about pin d?

A: We know that Forces acting at Joint D are shown in figure below Forces moving away from joints are…

Q: For the following items, answer whether the multiview projection matches the isometric drawing depic…

A: The given figure shows the different items, it is required to state whether the Multiview projection…

Q: 65 degree 6' - 17 degree 54'

A: 1 degree = 60' 65 degree 6' = 64 degree 66'

Q: Fullform of  PVDF

A: PVDF: Polyvinyl fluoride.

Q: +y") dx ly

A:

Q: Compute for the latitude of Line 1-2 A +4.81 B) +5.79 +8.03 D -18.63 Question 11 Compute for the…

A: Data is as given

Q: How are the sensitive parameters identified?

A: The process of determining probability of a variable of interest affected when value of one or more…

Q: Fullform of CASBEE

A: CASBEE has been designed to both enhance the quality of people's lives and to reduce the life-cycle…

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 4)…

A: 1. Deactivate the voltage source (V1):Set the voltage source V1 to zero (0 V). This means the…

Q: Figure 2. Inside perimeter Outside perimeter Centreline

A: Inside perimeter :Length×2+Breadth×2+2×2'+3'24'3''×2+12'×2+2×2'+3'=79'6''

Q: -0129 -077 R26

A:

Q: where did 3sqrt of 2 came from?

A: Given, A structure with carrying varying load   To find : Where 32 came from.

Q: For the given structures, determine the degree of indeterminacy. 3. 3

A: The given structure has two fixed supports at ends and one roller support in the middle. The fixed…

Q: Name three lines that intersect at point E.

A: Draw the figure. The lines which meets at the point E is the intersecting lines at point E. The…

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.