a. An eccentric load of 95 kN acts on a bracket as shown in Figure 6 at its free end. In the configuration shown in Figure 6, the seven (7) rivets are of the same diameter and the allowable shear stress is 10000 N/cm?. Neglecting the weight of the bracket determine the minimum rivet diameter required to avoid failure. 95kN

a. An eccentric load of 95 kN acts on a bracket as shown in Figure 6 at its free end. In the configuration shown in Figure 6, the seven (7) rivets are of the same diameter and the allowable shear stress is 10000 N/cm?. Neglecting the weight of the bracket determine the minimum rivet diameter required to avoid failure. 95kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 1 double-shear pin connections at Band D. All pins are 7 mm in diameter. a = 750 mm, b = 350 mm, h= 550 mm, P= 725 N, and 8 = 55° Determine the shear stress in pin B. Answer in MPa rounded-off to 2 decimal places. (1) a b P
15 kN 2) Two objects are glued on the angled plane as shown in figure. If the ultimate stress for the glued joint are 20 MPa and 10 MPa for tension and shearing stress respectively, find the value of 0 that corresponds to the maximum factor of safety and find the value of this maximum factor of safety. 0.035 m 0.05 m
Determine the maximum axial force that can be applied to the bar shown in Figure 3. The allowable stress is 100 MPa. The dimensions are: Hole diameter 20 mm. Thickness of bar: 6 mm D = 40 mm d%3D20mm Fillet radius, r = 4 mm 40mm 20 mm r 4 mm 20 mm Figure 3 P.
Calculate the maximum stress in a 25 mm thick perforated bar and show its location on the figure. 200 mm = 30 mm 5000 N 5000 N r= 15 mm
Please answer, thankyou
For the lap joint shown in the figure 1. Determine the maximum safe load P which may be applied if the shearing stress in the rivets is limited to 60 MPa 2. Determine the safe load P which may be applied if the bearing stress of the plate Is limited to 110 MPa (4-20 mm diameter rivet) O O →P
Part A The bolted connection (Figure 1) joins the bar supporting force P to two flanges set into a wall at A and B. In addition to supporting the load transferred by the bolt, the flanges are also subjected to additional 5-kN and 2-kN loads, as shown. Determine the largest internal shear force resisted by the bolt when P= 8 kN. (Figure 1) Express your answer to three significant figures and include appropriate units. Value Units Submit Request Answer Part B Determine the largest internal shear force resisted by the bolt when P = 23 kN and P = 18.6 kN. (Figure 2) Express your answer to three significant figures and include appropriate units. Value Units Figure Submit Request Answer SAN Provide Feedback Next > 2kN
QUESTION 1The pole ABC is loaded as shown in Figure 1.a. Determine the internal loadings acting at section a-a.b. Calculate the average normal stress and shear stress at section a-a if the pole has a uniform cross-sectional area of 400 mm2.Given AB = 0.6 m, BC = 1.0 m
@2 The support consists of solid brass post surrounded by a steel tube. Before the load is applied, the gap between these two parts is | mm. Given the dimensions shown in the figure, determine the greatest axial load that can be applied 0 the rigid cap A if the maximum allowable stress in brass is (Guiin)se = 150 MPa and the maximum allowable stress in steel is (Gun ) = 200 MPa. E, = 200 GPa and Ey,= 100GPa.