A. A three phase overhead line has A = 0.922, B = 140/70. The linedelivers 60MVA at 132KV and p,f.=0.8 lag.Draw the power circle diagram and find:-1) Sending end line voltage.2) Power angle.

The quantity of electrical charge that is moved over a certain period of time is measured by…

Answered: A. A three phase overhead line has A =…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A Three phase transposed line is composed of one conductor per phase with flat horizontal spacing of D as shown in the below figure. If GMD is 15.119 meters, then D will be a b D 2D Select one: Oa 12 meters Ob. None of these Oc15367 meters Od 14 meters
Give the correct voltage division-based equation to determine the voltage at V_bd. See diagram for reference.
Please neglect the simulation
Two single-phase transformers Trand Tz each rated at 500 kVA are operated in parallel Percentage impedances of and Tare (1 +16) and (0.8 +14.8), respectively. To share a load of 1000 kVA at 0.8 lagging power factor, the contribution of Tz (in kVA) is
What are FACTS (Flexible Alternating Current Transmission Systems) devices, and how do they enhance power system control?
3. Which one of the following method uses weak coupling between reactive power and voltage angle?. A. Newton - Raphson Method B. Decoupled Method C. Gauss-Seidal Method
Question Number 2 decent handwriting pls
A network consisting of a set of generator and load buses is to be modeled with a DC power flow, for the sake of conducting a contingency analysis. The initial flows calculated with the DC power flow give the following information: f°2-4 = - 65.3 MW and fº4-5 = 13.6 MW. The following values of LODF and PTDF factors are given: PTDF54,2-4 = -0.2609, LODF2-4,4-5 = -0.6087. Calculate the contingency flow on line 2-4 due to outage of line 4-5. Select one: O a. -75.5MW O b. None of these O c. -68.85MW O d. -73.58MW O e. 75.5MW O f. -61.75MW
12. Revi i. What difference you noticed in voltage regulation between RL and RC Loads? Why? i. Maximum voltage regulation occurs when power factor is In the case of inductive loads, for a fixed value of VR and I, the voltage regulation of the line increases with the ii. in power factor. iv, What are main reasons for voltage drop in transmission line?
Power system

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

A. A three phase overhead line has A = 0.922, B = 140270. The line delivers 60MVA at 132KV and p,f.=0.8 lag. Draw the power circle diagram and find:- 1) Sending end line voltage. 2) Power angle.