A wood beam AB on simple supports with span length equal to 10 ft is subjected to a uniform load of intensity 125 lb/ft acting along the entire length of the beam, a concentrated load of magnitude 7500 lb acting at a point 3 ft from the right-hand support, and a moment at A of 18,500 ft-lb (see Figure 6). Determine the minimum allowable value of h if the allowable stresses in bending and shear, respectively, are 2250 psi and 160 psi. 7500 lb 3 ft- 18,500 ft-lb b=8 in 125 lb/ft 10 ft Figure 6

A wood beam AB on simple supports with span length equal to 10 ft is subjected to a uniform load of intensity 125 lb/ft acting along the entire length of the beam, a concentrated load of magnitude 7500 lb acting at a point 3 ft from the right-hand support, and a moment at A of 18,500 ft-lb (see Figure 6). Determine the minimum allowable value of h if the allowable stresses in bending and shear, respectively, are 2250 psi and 160 psi. 7500 lb 3 ft- 18,500 ft-lb b=8 in 125 lb/ft 10 ft Figure 6

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

We have simply supported two-way slap as shown below. If the density of concrete is 2450 kg/m3, calculate the maximum bending moment in kN.m at beam A due to the un-factored self weight of the concrete slab. ... 7 m 7 m 5m Beam A
2. A beam with an inverted U section is loaded as shown. What is the max flexural stress developed and the max beam shear developed in the beam? 30mm 30mm 2m 6m 2m 200m 250mm 40mm
Problem 4: Calculate the angle of twist in a 3 inch diameter solid steel shaft that is 4 ft long. The shaft is stressed to its allowable shear stress of 9000 psi.
E5
The floor of a classroom is made of 150-mm thick lightweight concrete. If the floor is a slab having a length of 8m and width of 6m, determine the resultant force (in KN) caused by the dead load, the live load, and the total load. Note: lightweight concrete is 0.015KN/m2 per mm thickness & classroom is 1.92KN/m2
A cantilever timber beam with a span of L = 2.8 m supports a uniformly distributed load w. The beam width is b = 260 mm and the beam height is h = 210 mm. The allowable bending stress of the wood is 5.2 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w = i kN/m.
A floor sheathing is supported by 100 mm x 250 mm wooden joists spaced at 600 mm on centers with an effective span of 4.00 meters. The total floor load transmitted to the joist is 6.00 kPa. Using the weight of Joist as 6.50 KN/m³. and the modulus of elasticity E = 12000 MPa. Compute the actual bending stress, shear stress and deflection of the floor joist. Floor Sheathing Floor Joist Joist
4
Question 3 Part a: For the section shown, determine the: Maximum elastic Moment M Fully plastic moment Mf Shape factor a If loaded about the horizontal axis o, = 250MN/m²; E = 200GN/m² ● Part b: Determine the bending moment necessary to cause yielding to a depth of 10mm from the top and bottom surfaces. If after applying this load it is subsequently removed. What will be the residual stresses which will result at A and B when the load is removed? 10 40 Yielded region 40 Fig. 3a 10 ΝΑ Fig. 3b ΝΑ
A concrete beam is reinforced by three steel rods placed as shown. The modulus of elasticity is 3* 106 psi for the concrete and 30 *106 psi for the steel. Using an allowable stress of 1350 psi for the concrete and 20 ksi for the steel, determine the largest permissible positive bending moment in the beam.
A simply supported wood beam with a span of L = 15 ft supports a uniformly distributed load w. The beam width is b = 7 in. and the beam height is h = 13 in. The allowable bending stress of the wood is 860 psi. Determine the magnitude of the maximum load w that may be carried by the beam. b Answer: w = i lb/ft.