A wire 20 m long, weighing 0.8N per m, and having a cross sectional area of 6.2 mm2, is suspended vertically from its upper end, E = 103 GPa. Calculate the total elongation if a load of 220 N is attached to its lower end.

Q: uppose you are asked to conduct an experiment to study the impact of three factors(temperature: high…

A: Design of experiments (DOE) is nothing but a technique that is used to optimize the product cost and…

Q: In the drawing operation, technological property weldability is an important parameter. Select one:…

A: Drawing: It is a process in which uses tensile forces is used to stretch metal.

Q: Q4: State the advantage of electro polishing over mechanical polish

A: This question is based on the concept of electropolishing.

Q: What material would work best for milling abrasive material? O High speed steel Carbide

A: Some materials that are used as abrasives include Diamond most often used in ceramic grinding and…

Q: i still dont think i am getting the full working how you get to 0.32, am going to need to see the…

A: Given Data

Q: In the 3% error, why is the design acceptable?

A: Given: There are 3% error in the design. And by this error the developed power reduced from 0.556 MW…

Q: A sheet metal working company purchase a shearing machine from a surplus dealer without a flywheel.…

A:

Q: Can you rewrite the above solution as I cannot read some of the numbers and sketch elements?

A: Required:The Mohr's circle for each case.

Q: A material is required for a new product with fixed geometry that will be shaped by moulding. The…

A: When a material is selected to manufacture a material a lot of things are considered such as the…

Q: A sprue in a sand mould has a top diameter of 20mm and height of 200mm. The velocity of the molten…

A:

Q: The magnitude of true stain produced

A: Given: A bar is compressed to half to its original length.FIND:  Magnitude of true strain produced…

Q: Can you elaborate on answer ? Also what would be the answer for question b? I don't understand your…

A:

Q: Your design of process must start from a raw product and ends on the final finished product. Clearly…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: A shell of 100 mm diameter and 100 mm height with the corner radius of 0.4 mm is to be produced by…

A: Given:Shell diameter, d=100 mmHeight, h=100 mmcorner radius, r=0.4 mm

Q: 3- Calculate the number of finished goods (output) or N for the figure illustrated below:

A: Given: Total number of goods xi = 1200 Goods accepted after casting = 90% = 0.9 Goods sent for…

Q: Start a new Part in SolidWorks. Make a 1" diameter x 5" tall cylinder. Put a 0.5" diameter hole…

A: Given that-Diameter of cylinder = 1'' = 1 inchHeight of cylinder = 5'' = 5 inchDiameter of hole at…

Q: The main part of the product consists of a polyurethane sponge

A: • Strength & Durability:When the upholstery is produced using high grade resins, only a thinPU…

Q: Explain with neat sketch, the surface finishing process of “Sandblasting”. ( Minimum 1 and half…

A:

Q: B. What is the difference between the critical point and triple point? explain with drawing.

A: GIVEN DATA - TRIPLE POINT AND CRITICAL POINT GIVEN WE HAVE TO EXPLAIN IT WITH DRAWING

Q: How do you work with Sketch in SOLIDWORKS?

A: Given:- Solidworks software To find:- How to create a sketch and work in it

Q: (a) Figure 1 shows surface roughness and tolerances obtained in Chemical Machining (CM) and…

A: Chemical machining and electrochemical machining

Q: Without an applied load, an aluminum bronze, 9% (copper alloy) cylindrical rod has the following…

A:

Q: diagram briefly explain the construction and working of a Shaping

A: Surfaces are machined using a shaping machine. It is capable of cutting curves, angles, and a…

Q: What is required for a Swept Boss/Base in Solidworks? O A) Skecth (Profile) - 3D Skecth(Path) O B)…

A: The correct option is A.

Q: How did you get the temperature 367? What is the solution?

A:

Q: Give me the process of making a meat tenderizer using a shaper machine process. The picture below is…

A: As we know that it is a tool controlled by hand which makes mellow pieces of meat for cooking.

Q: answer with explanation in handwritten format

A: Given Solidworks option To find Function and explanation Solidworks is asoftware used for modeling…

Q: Thank you for your response. Please continue to provide the solution to the remainder of Part

A:

Q: The Sleeve Bearing Problem A machinist had pressed a new prelubricated, porous sintered bronze…

A: There may be following reasons of bearing failurePoor finishing on the bearing surface after…

Q: 1- Explain why a casting may have to be subjected to various heat treatments. 2- Describe the…

A: Given questions are related to manufacturing engineering and material science. Why a casting may…

Q: It is simple, help me to describe the part and write the steps of how to draw it in Solid Works

A: The assembly shown in the figure above is a fidget spinner. It is basically used as a toy. However,…

Q: (a) A turning operation is performed on a 060 mm cylindrical part of a certain alloy. The work…

A: Given: The diameter of rod, d = 50 mm The length of material, L1 = 140 mm The final length of work,…

Q: We have a rectangular piece. We wish to manufacture a parallel slot along thepiece in a vertical…

A: Given:To find:What is the number of blades used for the rough cutting steps?What is the number of…

Q: What is a chaplet?

A: Chaplet is a supporting element in casting process.

Q: this cylinder has a rod inside, around the rod there is paraffin wax that will expand, I want to…

A: Part -(a) use turning on lathe machineTo reduce thickness place the cylinder on the lathe machine…

Q: Hello ! I hope you are well. Why are we taking this specific cross section for the second part of…

A: In second part we have calculated the area which is as given below in the form of shaded region.To…

Q: Explain with neat sketch, the surface finishing process of “Sandblasting

A: