A wind tunnel is considered to be a steady-state operation, the system receives one hundred fifty pound- mass per minute of air at 215 psf, and 270 degrees Fahrenheit. The fluid is discharged from a point five meters above the datum/ reference point at 4,205 psf and 870 degrees Fahrenheit. Assuming that the velocity found at the inlet is 7,280 feet per minute and the Heat supplied is 530 BTU/min. During the process the density decreases by 15 percent and the internal energy is decreased by 1.05 horsepower. Determine the Work done in (a) Horsepower and BTU/s. (b) Considering the given on 3a, if the Work done is doubled, determine the Heat supplied during the process? (c) Considering the given on 3b, if Heat is doubled, what is the work done after 5 minutes? ´

A wind tunnel is considered to be a steady-state operation, the system receives one hundred fifty pound- mass per minute of air at 215 psf, and 270 degrees Fahrenheit. The fluid is discharged from a point five meters above the datum/ reference point at 4,205 psf and 870 degrees Fahrenheit. Assuming that the velocity found at the inlet is 7,280 feet per minute and the Heat supplied is 530 BTU/min. During the process the density decreases by 15 percent and the internal energy is decreased by 1.05 horsepower. Determine the Work done in (a) Horsepower and BTU/s. (b) Considering the given on 3a, if the Work done is doubled, determine the Heat supplied during the process? (c) Considering the given on 3b, if Heat is doubled, what is the work done after 5 minutes? ´

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A system receives 172 lb/min of fluid at the following initial properties: u1 = 2,731 kJ/kg;P1 = 16 kPa; v1 = 0.081 m3/kg; and 1 = 15 m/s. Exit properties are as follows: u2=2,795kJ/kg, P2= 37 kPa, v2=0.176 m3/kg; and 2 = 17.1 m/s. The fluid receives 1.2 kJ/s of heatas it goes through the system. Find the following:a. Work in kJ/kg.b. Work in 700 seconds. c. Power in MW.
Air flows through a long duct of constant area at 0.15 kg/s. A short section of the duct is cooled by liquid nitrogen that surrounds the duct. The rate of heat loss in this section is 15.0 kJ/s from the air. The absolute pressure, temperature, and velocity entering the cooled section are 188 kPa, 440 K, and 210 m/s, respectively. At the outlet, the absolute pressure and temperature are 213 kPa and 351 K. Compute the duct cross-sectional area and the changes in enthalpy, internal energy, and entropy for this flow. Take C=1 KJ/KgK, C,-0.717 KJ/Kg.K
The inlet temperature of an air compressor is T₁=300°K and the outlet temperature is T2-500°K. The compressor operates at a mass flow rate of 0.093kg/sec and the heat lost during the compression is 10kJ/kg. Assume that the air is an ideal gas with Cp=1.004 kJ/(kg°K). Calculate the mechanical power needed to be provided to the compressor shaft. Present your answer in kilo- Watts (kJ/sec).
20.3 cm diam 2.44 m 1.22 m Water Air at 105 kPa and 37°C flows upward through a 6-cm-diameter inclined duct at a rate of Q (L/s). The density of air at this temperature and pressure is 1.10 Kg/m³. The duct diameter is then reduced to 4 cm through a reducer. The pressure change across the reducer is measured by a water Air manometer. The elevation difference between the two points on the pipe where the two arms of the manometer are attached is 0.20 m. Determine the differential height between the fluid levels of the two arms of the manometer. Q (L/s) 90
The feed to a compressor is superheated steam at 310°C and 40 bar. It enters the compressor at a velocity of 17 m/s. The pipe inlet inside diameter is 0.25 m. The discharging pipe, after the compressor, has a smaller inside diameter and the discharge velocity is 120 m/s. The exit of the compressor is superheated steam at 350°C and 85 bar absolute. Heat loss from the compressor to the surroundings is 3 kW. Determine the compressor horsepower
An ideal gas passes a diffuser. At the diffuser inlet, the temperature is T1 = 350.00 K, the pressure P1 = 100.00 kPa, the velocity V1 = 200.00 m/s, and the inlet area A1 = 0.30 m2. At the exit, the velocity is very small. The specific heat of the ideal gas at the constant pressure is cp = 1.0050 kJ/(kg·K). The gas constant is R = 0.2870 kPa·m3/(kg·K). Determine the mass flow rate __________(kg/s)
Air (MW=29 g/mol) at 115.00 kPa and 285.00 is compressed steadily to 600.0 kPa. The mass flow rate of the air is 2.00 kg/s and a heat loss of 32.1 kW occurs during the process. You may assume that changes in kinetic and potential energy are negligible, the temperature of the surroundings is 25 ∘C, and that the CP of air is 3.5 R. Given the compressor operates with a second law (reversible) efficiency of 0.60,calculate the following. What is the actual work interaction term in kW? What is the actual exit temperature of the air in Celcius?
Steam enters a horizontal turbine at 350 lbf/in² absolute, 580°C, and 12 ft/s and is discharged at 110 ft/s and 25°C saturated conditions. The mass flow is 2.5 lbm/s, and the heat losses are 187 Btu/lb of steam. The enthalpies h₁ and h2 are 3.92E7 ft·lbf/slug and 2.74E7 ft·lbf/slug, respectively. If head losses are negligible, how much horsepower does the turbine develop? hp
14A fluid flows at a speed of 7.5 m/s in a pipe with a diameter of 35 cm. What is the power, in W, of the pump to overcome the irreversible pressure drop when the pressure drop along the pipe is calculated to be 6300 Pa?
A wind tunnel is considered to be a steady-state operation, the system receives one hundred fifty pound- mass per minute of air at 285 psf, and 270 degrees Fahrenheit. The fluid is discharged from a point five meters above the datum/ reference point at 4,255 psf and 750 degrees Fahrenheit. Assuming that the velocity found at the inlet is 6,285 feet per minute and the Heat supplied is 580 BTU/min. During the process the density decreases by 15 percent and the internal energy is decreased by 1.05 horsepower. Determine the Work done in (a) Horsepower and BTU/s. (b) Considering the given on 3a, if the Work done is doubled, determine the Heat supplied during the process? (c) Considering the given on 3b, if Heat is doubled, what is the work done after 6 minutes?
A wind tunnel is considered to be a steady-state operation, the system receives one hundred fifty pound- mass per minute of air at 220 psf, and 250 degrees Fahrenheit. The fluid is discharged from a point five meters above the datum/ reference point at 4,275 psf and 750 degrees Fahrenheit. Assuming that the velocity found at the inlet is 8,275 feet per minute and the Heat supplied is 580 BTU/min. During the process the density decreases by 15 percent and the internal energy is decreased by 1.05 horsepower. Determine the Work done in (a) Horsepower and BTU/s. (b) Considering the given on 3a, if the Work done is doubled, determine the Heat supplied during the process? (c) Considering the given on 3b, if Heat is doubled, what is the work done after 7 minutes?
A wind tunnel is considered to be a steady-state operation, the system receives one hundred fifty pound- mass per minute of air at 200 psfg and 240 degrees Fahrenheit. The fluid is discharged from a point five meters above the datum/ reference point at 4,155 psf and 550 degrees Fahrenheit. Assuming that the velocity found at the inlet is 7,005 feet per minute and the Heat supplied is 515 BTU/min. During the process the density decreases by 15 percent and the internal energy is decreased by 1.05 horsepower. Determine the Work done in (a) Horsepower and BTU/s. (b) Considering the given on 3a, if the Work done is doubled, determine the Heat supplied during the process? (c) Considering the given on 3b, if Heat is doubled, what is the work done after 9 minutes?