A winch at point B is used to slide a box up a chute CD in a warehouse. If the component of the force from cable AB in the direction of the chute must be 410 lb, determine the force in the cable for the position of the box given below. The chute is parallel to the .xz 1 plane. Neglect the size of the box and the winch. The box is the distance up the chute from point C.

A winch at point B is used to slide a box up a chute CD in a warehouse. If the component of the force from cable AB in the direction of the chute must be 410 lb, determine the force in the cable for the position of the box given below. The chute is parallel to the .xz 1 plane. Neglect the size of the box and the winch. The box is the distance up the chute from point C.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: T(t) Cable B. F(t) 600 N - 360 N M t=12s t=24s The winch, shown in the figure, delivers a horizontal…

Q: The beam shown is supported by a hinge at 'A' and a roller on a 3 to 4 slope at 'B'. Determine the…

Q: The block has a mass of 150 kg and rests on a surface for which the coefficients of static and…

Q: Current Attempt in Progress The solid 27 mm diameter steel [E = 200 GPa] shaft supports two belt…

Q: A system of cables is shown and in a state of equilibrium. Using equilibrium equations, solve for…

A: To find tension in cable AB, BC, CD

Q: Example 2: A suspended cable is hung between two points, of the same level, and is subijected to a…

A: Draw FBD:

Q: The system in the figure is in equilibrium. Aconcrete block of mass 349 kg hangs from the end of the…

Q: A 4-kg sphere is connected to wire ACB through a ring C. The sphere revolves at a constant speed in…

A: The given data is shown below: Mass of sphere=4kgRadius=2.4mα=35°β=45°

Q: B ... 4m 2m Hinge Water 50cm 420cm 30cm A closed cylindrical drum is 30cm in diameter and 50cm high…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: P=545N To find tension in cable BE and BD

Q: THE 10-FT CABLE AB IS ATTACHED TO TWO COLLARS AS SHOWN. THE COLLAR AT A CAN SLIDE FREELY ALONG THE…

A: Given: Length of cable = 10ft Determine- a=?

Q: cylinder is in 1. Determine the moment of this 4.4-kN force about the boom pivot point O. The moment…

A: ##Calculation of moment about pivot point O due to 4.4 KN ###

Q: The following shape represents a circular gate where the radius of arc AB=4m, distance BC=6m. If the…

Q: The 540-lb cylinder at A is hoisted using the motor and the pulley system shown. The speed of point…

Q: In the Figure shown, calculate the mass of the cylinder is 200 kg and that of member AB is 50 kg.…

Q: Problem 3. Object B weighs 100 lb. The brown cable that passes over pulley D and around pulley C…

Q: 3. Three cables are joined at the junction ring C. A Determine the tensions in cables AC and BC…

Q: force water. Determine the force & angle on gate AB.

Q: 2. The center of gravity of the 50-kg spool is at G. A cable wound around the hub of the spool is…

Q: We have a table that we seek to lift with a pulley. The table is uniform, with a weight of 73…

Q: Determine the shear force, S, in the web at section 1. Provide your answer in newtons (N) to the…

A: The given figure is shown below:

Q: Very urgent. The box in the figure is connected by a cable from point A to point B. If the stress T…

Q: 3 m P 3 m B 1.5 mi 3 m E 3 m 1.5 m

Q: Given: 0A OB Find 4 A chair is suspended from two different cables, AC and CB. B . the combined…

Q: The uniform 15-m pole has a mass of 175 kg and is supported by its smooth ends against the vertical…

Q: Solve for the minimum tension on the cable necessary to open the circular gate AB. Neglect the…

Q: Homework 1 Q1) The frame shown below supports 100lb weight. The cable is attached at A and passes…

Q: The 6-m pole ABC is acted upon by a force P as shown. The pole is held by a ball-and-socket joint at…

A: Given:- The length of the pole ABC = 6 m The magnitude of the force acting on pole = P The tension…

Q: For the quarter circle gate BC with a hinge at C, the force P = ... kN to hold the gate stationary…

A: Radius=4.5m Widht=5.5m

Q: A steel plate shown has a thickness of 10mm and to be supported in a horizontal position by vertical…

A: Whenever any structure is supported by the cables or any support structure, then that cable shows…

Q: B. Determine the support reactions at A, C & D of the loaded beam. 150 KN 45KN/m B 1.0 m 3.0 m 1.50…

A: To Determine Reactions at support A,C,D. There is no horizontal force, hence no horizontal reaction…

Q: The two blocks started at rest. The surface of the inclined plane is frictionless. (note: neglect…

Q: he weights of the two boxes are W1 = 120 lb. and W2 = 80 lb. The coefficients of riction between the…

A: a. The box should be stationary. The free body diagram of box W2 is given below. Consider the…

Q: A metal boom OA Is shown in the figure below is supported by 2 cables AC and AB and held in pesition…

Q: Given that M = 34 kg, 0 = 35° and ø = 25", determine the tension developed in wires ČA and CB…

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

A winch at point B is used to slide a box up a chute CD in a warehouse. If the component
of the force from cable AB in the direction of the chute must be 410 lb, determine the
force in the cable for the position of the box given below. The chute is parallel to the xz
1
the distance up the chute
plane. Neglect the size of the box and the winch. The box is
from point C.
105in.
Z
B (-45, 0, 130) in.
135in.
40 in
y
FAB
=
lb

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The light right-angle boom which supports the 360-kg cylinder is supported by three cables and a ball-and-socket joint at O attached to the vertical x-y surface. Determine the reactions at O and the cable tensions. A Ox - Answers: IM TAC = i Me C 0.65 m y 1.05 m! 0.65 m 10 B 360 kg 1.30 m 2.30 m N Oy E 1.45 m II D N TBD = 1.45 m Hr x N O₂ = Mi N TBE = i N N
The motor exerts a force of F = (18.4t? ) N on the cable, where t is in seconds. Determine the speed of the 23.7-kg crate when t = 4.7 s. The coefficients of static and kinetic friction between the crate and the plane are µs = 0.35 and Hk = 0.23, respectively. A
A boom consists of a 100-mm-diameter steel pipe AB and a cable BC as shown in the figure. The modulus of B P -3.6 m PROB. 17.4 1.5 m A steel E 200 X 106 kPa. Determine the capacity P of the boom. Use the Euler formula with a factor of safety of 3. Neglect the weight of the pipe. Section properties of pipe: A = 2.05 x 10³ mm² and the radius of gyra- tion r = 38.4 mm.
i need the answer quickly
In this statics problem I am given a triangular distributed load on a cable. Attached is the given info for the problem. I know the basic steps to complete the problem but I am having issues figuring out where the triangular distributed load and 15 degrees given work into the problem. I’ve tried finding the Moment around B with the distributed load and then the two components of Tension at A (using sin(15) and cos(15) respectively but this did not work.
A
ENGINEERING MECHANICS If the motor exerts a constant force of 300 N on the cable, determine the speed of the20-kg crate when it travels s= 10m up to the plane, starting from the rest. Thecoefficient of kinetic friction between the crate ant the plane is μ = 0.3. Determine: (a) The work done by all the forces as the block moves 10m to the plane. Sketchtogether the free body diagram. (b) The work done by all the forces as the block moves 12m to the plane with pullingforce of 400N with an angle of 50°. Mass of the object is added with 6kg.Coefficient of friction is 0.50. Sketch together the free body diagram.
A system of cables is shown and in a state of equilibrium. Using equilibrium equations, solve for the absolute value of P (in kN).
The small crane is mounted along the side of a pickup bed and facilitates the handling of heavy loads. When the boom elevation angle is 0 = 37°, the force in the hydraulic cylinder BC is 4.1 kN, and this force applied at point C is in the direction from B to C (the cylinder is in compression). Determine the moment of this 4.1-kN force about the boom pivot point O. The moment is positive if counterclockwise, negative if clockwise. 610 mm 105 mm 285 mm 345 mm B Answer: Mo = kN-m
If the mass of cylinder A is 40 kg, determine the mass of cylinder C in order to hold the assembly in the position shown. (Assume the pulley at B to be perfectly smooth) D A E 30° 40 kg B
Two blocks A and B, each having a mass of 5 kg, are connected by the linkage shown. If the coefficient of static friction at the contacting surfaces is μ = 0.5, determine the largest force P that can be applied to pin C of the linkage without causing the blocks to move. Neglect the weight of the links. B 30° 30° 30° A