A - Whilst drilling (8 3/8") section, at depth (9600 ft) a well kick was detected and the well was shut-in. Drilling supervisor instructed the mud engineer to increase mud weight from (9.8 ppg) to (10.2ppg) to control the well. 1- Determine the required amount of Barite (in sacks), to increase the mud density (9.8ppg-10.2ppg).

A - Whilst drilling (8 3/8") section, at depth (9600 ft) a well kick was detected and the well was shut-in. Drilling supervisor instructed the mud engineer to increase mud weight from (9.8 ppg) to (10.2ppg) to control the well. 1- Determine the required amount of Barite (in sacks), to increase the mud density (9.8ppg-10.2ppg).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Quize (3): A soil sample is subjected to an all-round pressure of 100 kN/m, the pore water pressure was 93 kN/m. With the drainage valve remains closed an increment of principal stress difference (o, -o,) was applied causing the pore water pressure to increase to 133 kN/m. Knowing that A-0.4, determine B and (o, -a,). 1 Add file
3- A sand sample is subjected to drainage cutting test with a hollow cylinder device. Rupture occurs with increasing internal pressure while external pressure is constant. At the moment of rupture, the external stress is 200 kPa and the internal stress is 300| Kilopascals - be. Internal and external radii of the sample are 40 and 60 mm. A) Obtain the angle of soil friction. B) At the moment of rupture, what is the axial stress applied to the sample?
يمل
Question: Choose the appropriate word to fill in the blank in each of the following sentences. A. In rotary drilling the drilling processes accompanied by Pumping water with... ..(1- cement, 2-sand,3-clay). B. Bentonite can be used on the hole through perforated pipes to reduce the friction of the rotating shaft and thus........ the speed of drilling. (1- increase,2-dicrease, 3-hardining). C. A loose.........sample is a soil sample whose structure is disintegrated and whose mechanical properties have changed during its extraction. (1- undisturbed,2-disturbed ,3- compacted). D. There are some tests that require a.....and undisturbed Sample, such as shear, permeability, sittlement and others [soild, loose, soft]
Identify the type of soil that contains wide variety of particle sizes ranging from clay to gravel Marine Soils Boston Blue Clay Ob. Bedrock Glacial Till
A - Whilst drilling (8 3/8") section, at depth (9600 ft detected and the well was shut-in. Drilling supervi mud engineer to increase mud weight from (9.8 ppg control the well. 1- Determine the required amount of Barite (in sack mud density (9.8ppg-10.2ppg). 2- The mud engineer started to weighting up th- adding the required Barite the final mud density to poor suspension properties of the mud (low-Y amount of settled Barite in (Kg)? And wha recommendations/practices to avoid such issue? 3- After killing the well, drilling was resumed an massive bed of Anhydrate was penetrated. expect mud contamination be? And recommendations? Given data: Mud in tanks = 200 m³ Barite sack= 25 kg Barite density = 4.3 gm/cc 1 m³=6.28 bbl Best wishes .
A series of identical samples have been tested with drained triaxial test and some of the values are given in the tabulated table 3(Below). Calculate the remaining values as in the blank box. PARAMETER |cell pressure, o3 (kPa) total axial stress, 01 (kPa) pore pressure at failure, u¡ (kPa) |change in volume, Av effective cell pressure, o3' (kPa) effective total axial stress, o,' (kPa) |difference in stress, q (kPa) CD test 150 284 i 1.8 ii i iv O i = 134; ii = 16; iii = 150; iv = 0 O i = 134; ii = 284; iii = 150; iv = 0 O i = 0; ii = 16; iii = 150; iv = 134 O i = 0; ii = 150; iii = 284; iv = 134
11.14 The time for 50% consolidation of a 1-in. thick clay layer (drained at top and bot- tom) in the laboratory is 2 min, 20 sec. How long (in days) will it take for a 8-ft thick layer of the same clay in the field (under the same pressure increment) to reach 30% consolidation? In the field, there is a rock layer at the bottom of the clay.
Solve and explain mention answer also
The time for 50% consolidation of a 1-in. thick clay layer (drained at top and bottom) in the laboratory is 2 min, 20 sec. How long (in days) will it take for an 8-ft thick layer of the same clay in the field (under the same pressure increment) to reach 30% consolidation? In the field, there is a rock layer at the bottom of the clay.
Geotechnical , Civil engineering , please solve question 4 (part d)
A SPT test was performed in a sandy soil layer (y = 115 pcf) at a depth of 16 ft. below the ground surface. The SPT blow counts were recorded as x-y-z, where x, y and z are the last three digits of student ID. The test was conducted using a safety hammer in a 6 in. diameter exploratory boring using a standard sampler with the liner installed. Compute energy-corrected N60. (N1)60 with overburden correction, angle of friction - ', and relative density Dr of soil. Assume D50 = 0.2 mm. Factor Equipment Variable Term Correction CE = ER/60 0.5 to 1.00) 0.7 to 1.20 0.8 to 1.51) Donut Hammer Energy Ratio %3D Safety Hammer Automatic Hammer Borehole 65 to 115 mm Св 1.0 Diameter 150 mm 1.05 200 mm 1.15 Sampling method Standard sampler Cs 1.0 Non-standard sampler 1.1 to 1.3 Rod Length 3 to 4 m CR 0.75 4 to 6 m 0.85 6 to 10 m 10 to >30 m 0.95 1.0 'Values presented are for guidance only. Actual ER values should be measured per ASTMD 4633