A weight of 18N is supported by a linear spring having a stiffness of 4 N/m and a dashpot having a damping coefficient of 56 Ns/m. If the mass has an initial displacement of 4 mm and an initial velocity of zero, find the following parameters: а. General Solution Frequency of the system Phase Angle b. с. d. Amplitude

Q: State three uses of the combination set

A: Combination set is an measuring tool, it is used to measure angles and lengths.

Q: How many turns does cog E make?

A:

Q: How did you solve for the velocity of b?

A: The given question was solved using velocity polygon method.If AB is a link which is rotating about…

Q: Sketch the figure using AutoCAD and hatch the lines with colours . mention the dimesions as shown in…

A:

Q: Find the value of a. TO a. Vs +3

A:

Q: The pictured disk which weighs 20 lbs. and contacts an inclined surface (this inclined surface is…

A:

Q: The beam AB is homogeneous and has a mass of 5,191. The tension in the cable of the crane can not…

A:

Q: 10) in the following figure, if h2-10" and h1=5", then, the angle of taper equal 10" Ⓒa. 60⁰ Hand…

A: These are small blocks of alloy steel. Used in the manufacturing shops as length standards. Not to…

Q: Ax R.70 4x 1.40 B This part contains 4 holes with radius 0.375 inches 1.00 This part contains 4…

A: Select the correct statement about the notation circled in green and marked as letterA. Assume all…

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: Consider a virtual load Q, acting vertically downwards, is applied at point A.Draw the given truss…

Q: Problem 1: a) Draw the free body diagram of the member ABC? b) Determine the reaction forces at the…

A:

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one:…

A:

Q: The figure shows a shaper machine that uses Whitworth quick return mechanism wherein the different…

A: Given Data OA=75cm OP=50cm CA=150cm CD=135 cm

Q: Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to…

A:

Q: The steel box wrench (E=29,000ksi, v=0.32) is loaded with a 40-lb horizontal force and a 25-lb…

A:

Q: Find the angle e for the given figure 800 N y 8 3 O a. 63 О ь. 59 с. 69 O d. 66

A: From the given figure...

Q: Members ABC and DEF are joined with steel links (E = 200 GPa). Each of the link is made of a pair of…

A:

Q: A 2.10kg pole is attached to a wall with a hinge as shown. A 5.80kg sign is suspended at the other…

A: Given data: mp=2.10 kgM=5.8 kgD1=1.3 mD2=3.2 mα=19.0° Need to determine the torque on the pole due…

Q: What is Line J? ARROWHEAD .35mm A 7.0 В

A: Solution:

Q: The number of teeth on a gear is 27 and the outside diameter is measured as 10 mm. The module of the…

A: Given Data No. of teeth is 27 Outside diamtere is 10mm

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: Draw the and B A.F.D&S.F.D& B.M.D (KN.M

A: To draw axial ,shear and bending moment diagram

Q: Choose the correct word to complete the -5 following sentence: The fault was.......... .None of the…

A: Correct answer: (c) undetected

Q: Determine the sequence for the following figure

A: Given: To find: Sequence

Q: Create a table showing wrench sizes in metric and U.S. units.

A: Following are the wrench sizes in metric and U.S. units.

Q: can you draw the FBD

A: There are four rivets in this problem. In ideal case load will be equally distributed. Each rivet…

Q: What is Line G?

A: Solution: