Short answer questions 1. Draw the strain-stress curve of the mild steel. 2. What is a doubly reinforced beam? When a doubly reinforced section should be adopted? (

Q: A piston-cylinder device contains 1.5 kg of steam at 300°C and 0.4 MPa. Steam is cooled at constant…

A: The initial conditions are: The specific volume of the steam can be determined from the steam table…

Q: 355 coupe for some maintenance check. Before proceeding to your regular maintenance routine, it is…

A: Odd matric number:

Q: 2 Constraint indicated the name and where it should be

A: Given: To find: Where the constraint should be

Q: What is the value of w and y? y W 6V2

A:

Q: Choose one of the following statements which is not true.

A: for solution refer below images.

Q: Compute the moments of inertia with respect to the X-X and Y-Y centroidal axes for the following…

A:

Q: Sorry that's the wrong answer it is 0.62

A: Power coefficient = Cp=0.24 Wind speed = Vw=10.3 m/s Blade length = R = 34 m The power generated by…

Q: A pneumatic system operating at 85 psi comprises a series of pneumatic actuators which consume 2.4…

A: Original CFM = 2.4 CFMOriginal pressure= 85 psiNew pressure= 120 psiAtmospheric pressure= 14.7 psi

Q: A 2.10kg pole is attached to a wall with a hinge as shown. A 5.80kg sign is suspended at the other…

A: Given data: mp=2.10 kgM=5.8 kgD1=1.3 mD2=3.2 mα=19.0° Need to determine the torque on the pole due…

Q: Question attached

A: (a) Relative humidity is the ratio of the partial pressure of water vapour in the mixture to the…

Q: What did you put in the calculator to get the box answers? Please put exactly what you put

A: The solution provided in the previous response is as follows.

Q: 1.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: Sure, based on the information provided in the text accompanying the image, the angle between lines…

Q: now please answer question 2 and 3 please

A: This question is based on the concept material science. As per the guidelines we are subjected to…

Q: A midsized Dozer weighs 41,000 pounds and has 175 hp. If the machine is working at 80% efficiency…

A: Given Data The weight of the machine is: W=41000 lb The power is: P=175 hp The efficiency of the…

Q: A gas has an initial temperature of 25 degrees Celsius. It is cooled until its temperature reduces…

A: final temperature = 22.5o CExplanation:Approach to solving the question: Detailed explanation:…

Q: 1-8. Determine angles a, b, and c (Figure P1-8). a 35° FIGURE P1-8

A:

Q: I will rate you with “UPVOTE/LIKE” if you answer every question.   I will rate you with “DOWNVOTE/

A: Given Data : Definitions Moment Principle

Q: This answer was marked incorrect

A: The power input to the pump is 0.454 kW.

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.