A water softener has 0.1 m3 of ion-exchange resin with an exchange capacity of 100 kg/m3 . The consumption rate is 5,000 L of water per day. If the water contains 270.0 mg/L of hardness as CaCO3 and it is desired to soften it to 85 mg/L asCaCO3, how much should be bypassed? What is the time between regeneration cycles?

Q: The use of rather than irregularly shaped aggregate also give - workability. * Smooth surfaces give…

A: Option  1 and 3 is correct.

Q: In the figure below, a stainless steel wire is supporting a weight, W. The Yield Strength and…

A:

Q: A cylindrical aluminum alloy rod with a 0.5 in. diameter is subjected to ten- sion. Determine the…

A: Diameter of rod, d = 0.5 in Change in diameter, ∆d = -10-4 in Young’s modulus, E = 11x106 psi…

Q: Which of the following is the best representation of the samples' (A and B) axial strains when…

A:

Q: A material has a mass of 83 g before abrasion and the abrasive ratio is 1.75. If the area of…

A:

Q: Once in civil engineering, what is the minimum curing period typically recommended for concrete…

A: In civil engineering, the minimum curing period for concrete structures typically depends on the…

Q: A 7075-T651 alloy is used in a structural component in an airplane. The component must not fail when…

A: Approach to solving the question:Identify the relevant information provided in the problem…

Q: A 1.2-ff³ block of aluminum is tied to a piece of cork (SG=0. as shown What yolume of cork is…

A: Draw the free body diagram of aluminium block Here,  FB1=Buoyant force on aluminium T= Tension in…

Q: Compare and contrast the three (3) methods of manufacturing plastics

A: Manufacturing of plastics - Plastics are manufactured from ethane and propane, which are processed…

Q: Abr= 290 mm? A,= 380 mm? A= 290 mm? 2m 1.5m 3P 8m FIND THE LARGEST VALUE OF P THAT WILL NOT EXCEED…

A:

Q: Identify defects that may occuron materials based on their performance on wastewater treatment plant

A: Clean water is an essential resource for people and their environments throughout the world. Those…

Q: The bulk modulus of elasticity of H20 is equal to 2.2Gpa, what pressure is required to reduce the…

A: Bulk Modulus of Elasticity: It is one of the mechanical property of solids. Bulk modulus is a…

Q: It is a kind of wastewater treatment where used water course through a series of aggregates to…

A: During the process of filtration, Sand Filters(rapid sand filter, slow sand filter) are using course…

Q: If the pressure at the bottom of an open tank is 713 kPa, find the unit weight (kN/m) of titanium in…

A: Given:  Pressure at bottom open tank =713 kpa. Depth of liquids. Specific gravity of liquids. To…

Q: 8.30 Ifa component fabricated from an S-590 alloy (Figure 8.30) is to be exposed to a tensile stress…

A: The given tensile stress is 300 Mpa Temperature- 6500 C Estimate its rupture strength using the…

Q: To manufacture a piston with a circular cross section, an alloy steel bar is required whose length…

A: Elastic limit is defined as the strain on the stress-strain graph, beyond which the material…

Q: 10/10 FIND STRESS IN Aluminum. IF E st= 200000 MPa, Ealu.=70000 .MPa 100 kN RALU=30 MM Aluminum…

A: Given data Loading Youngs modulus of both materails  Radius  of bith material

Q: Determine the modules of resilience of aluminum allow with yield strength of 40000 psi

A:

Q: Argillaceous materials are those: Owhich have lime as the main constituent O which easily break when…

A: Argilliacceous materials are fined grained aluminosilicates such as kaolinite, illite,…

Q: 14.2 lb/in2 --------> lb/ft2

A: Given a pressure value of 14.2 in lb/in2. This has to be converted into lb/ft2.

Q: Rnd the valu

A: Data given Q = 10 lps    = 0.01 m3/s Diameter,            D1 = 0.1 m                             D2…

Q: Q-One of the most important factors that construction materials depend on for their moisture…

A: Given : The construction materials depend upon which factor for their moisture resistance

Q: Question 9 At desorption, the EMC of wood will be lower higher O than at adsorption at a given RH.

A:

Q: What is the major use for ABS plastics?

A: ABS plastic, also known as Acrylonitrile Butadiene Styrene, is an opaque, amorphous, and…

Q: n engineering design requires a glass component to withstand high service temperature of around…

A:

Q: The the size of the aggregate, the--------- is the surface area and hence --amount of water is…

A: The more the size of the aggregate, the high is the surface area and hence reduction amount of water…

Q: 4.) A cylindrical rod 100 mm long and having a diameter of 10.0 mm is to be deformed using a tensile…

A: Length of rod (L)  = 100 mmDiameter of rod (d) = 10 mmC/s Area of Rod (A) = π4d2 = π4×102 = 78.54…

Q: Q2/ Sorting the engineering materials (Metals and Ceramics) from lowest to highest value according…

A:

Q: Q12 (a) Differentiate between the “soft constraints" and “hard constraints". (b) You are required to…

A: The stress is a quantity that differs from the amount of strain in the system and also the rigidity…

Q: What is the difference between ductility and malleability  b ) what is the difference between…

A: Solution: 1.  Ductility Malleability 1) Elasticity is the property of any solid material by…

Q: A) A specimen of alloy having the following engineering stresses produces the corresponding plastic…

A: Given above table and we have to find the engineering stress which produces engineering strain of…

Q: For 4340 steel, the fracture toughness and yield strength depend on the prior heat treatment, as…

A: When a material is subjected to stress less than its yield stress, it will only experience elastic…

Q: C) WHAT DOES QS CONTROL'S? D) WHAT DOES THIS MEAN'S ? ED HOW DO WE CALCULATE F) HOW DO WE CALCULATE…

A: CQs in the section controls for the strength of the welded sectionD this means minimum size of weld

Q: Fill in the blanks with appropriate words a) Fibers are not ……………………… Therefore heat is only…

A: Given series of Fill in the blanks and asked to fill with appropriate words1. Fibres are not…

Q: Explain the difference between various grades of OPC. EXPLAIN POZZOLANIC ACTION.

A:

Q: In pressure grouting technique, the slurry contains * O PFA microsilica all of the mentioned O…

A: Grouting : Grouting is technique which is used to increase the strength of soil . In pressure…

Q: During the construction of the waffle slab, they use _____ in the shuttering to shape the waffle…

A: Waffle slab are plain on its top which is thin and contains grid system at its bottom which is…

Q: The flange of an S275 beam is 53.3 mm thick. What is the yield strength of the beam in N/mm2?…

A: Given, S275 Beam The thickness of flange=53.3 mm

Wind Energy

Wind energy is a renewable energy source that is used to generate electricity by wind power. The term, wind power, means utilization of kinetic energy of wind to generate electricity. Wind energy is termed renewable source energy because it can never be exhausted. There are other renewable energy sources, such as solar energy, geothermal energy, hydropower energy, and so on. All of them contribute to power the thermal energy stations to generate electricity.