A home water softener has 0.1 m³ of ion exchange resin with an exchange capacity of 57 kg / m³. The occupants use 2000 L of water per day. If water contains 280 g mg/L of hardness as CaCO3 and it is desired to soften it to 85 mg/L as CaCO3. (i) The time percentage that should be by passed?

A home water softener has 0.1 m³ of ion exchange resin with an exchange capacity of 57 kg / m³. The occupants use 2000 L of water per day. If water contains 280 g mg/L of hardness as CaCO3 and it is desired to soften it to 85 mg/L as CaCO3. (i) The time percentage that should be by passed?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Chose the correct answer 1- The Unit measurement of suspended solids is ...A- kg 2- The Unit measurement of Turbidity is A- °C is B-m B-NTU C- mg/L C-K 3- The Unit measurement of pH www A-mg/L 4- The Unit measurement of alkalinity is .. 5-Non toxic metals includes 6-Dissolved materials size is lees than A- 10 mm D- none of above D- none of above D- none of above B- p.p.m C- g/m³ D- none of above A- m/sec B- m³/sec C- mg/L A-Chromium B- Mercury C- Calcium D- none of above B- 106, C-108 mm D- none of above mm 7- Public standards of Hardness in drinking water is A-500 mg/L B-50 mg/L C-100 mg/L D- none of above 8- Alkalinity species includes are A-HCO3 B-CO3 C- OH D-All of above ... 9- Dental cavities in children can prevented when Drinking water has Fluoride concentration of A- 0.1 mg/L B- 1 mg/L C- 10 mg/L D- none of above 10- Toxic metals are metals that harmful to humans even when exists in concentration of .. A- Small B-Large C-zero D- none of above
10) Table 1 and Table 2 list the general properties and the production alternatives for various pozzolans. |Table 1 Chemical Composition SiO2, % B D 35 93 35 50 A½O3, % Fe3O2, % Саб, % Physical Property Blaine fineness, m²/kg Color 20 0.4 12 25 0.4 10 25 1.6 40 5 430 Gray 19,000 Gray 400 White 390 Gray Production Method a byproduct of producing silicon metal or ferrosilicon alloys 2 Table 2 a by-product in coal fired power stations formed when molten iron blast furnace slag is rapidly chilled (quenched) by immersion in water A dehydroxylated form of the clay mineral kaolinite 3 For the four pozzolans given in the first column of Table 3, fill the remaining columns with the corresponding letters and numbers: • Column 2 - Determine which one is which pozzolan (from Table 1): (A/B/C/D) • Column 3 - Identify the natural and artificial pozzolans: (N/A) • Column 4 - Determine which ones are self-cementing. Column 5 - Determine the production method (from Table 2): (1/2/3/4) Table 3…
A 1g granular powder have the following data below, compute for the following: Volume of the solid alone = 1 cm3/g Volume of intraparticle pores = 0.2 cm3/2g Volume of spaces between particle = 3.2 cm3/g Volume after tapping = 2.4 cm3/2g Note: Answer should be in three decimal places A) Specific volume = ? cm3/g B) Specific granule volume = ? cm3/g C) Specific bulk volume = ? cm3/g D) Total porosity = ? E) Interspace porosity = ? F) Intraparticle porosity = ? G) Hausner ratio = ? H) Carr's compressibility index = ?
I need the answer as soon as possible
I will rate immediately, thank you!
A certain oil has a viscosity of 0.00070 Pa-sec. It is to lubricate plates. What shear force is required to deform the oil at a strain rate of 7000/sec? (Area of the plate is 1.2 sq. m) O 5.88 kN O 5.88 N O 4.08 kN O 4.08 N
The granulation step is a very important step in the preparation procedure of ceramics. During the preparation of granules in a production facility, it has been observed that the granules in Figure 2 are obtained as a result of the process, while the granules are requested to be prepared as in Figure 1. a) What do you think are the reasons for the formation of granules in this way? (Write and explain 3 reasons). b) What precautions would you take to prevent this error from occurring in the next step? (Write and explain 2 precautions).
I need the answer as soon as possible
Explain what is setting time, slump value and workability of conrcete having Plasticiser Superplasticizer Hyper plasticizer
3.3 If an ion exchange water softener has 0.2 m of ion-exchange resin with an exchange capacity of 75 kg/m'. The occupants use 2500 gallon/day of water per day. If the water contains 250 mg/L of hardness as CaCO3 and it is desired to soften it to 90 mg/L as CACO3, what is the time between b) 14 days regeneration? a) 15 days c) 12 days d) 10 days
A liquid compressed in a cylinder has a volume of 1000 cm³ at 2MN/m² and a volume of 993 cm³ at 3.3 MN/m². What is the bulk modulus of elasticity?
A cylindrical rod with a length of 380 mm and a diameter of 10 mm is to be subjected to a tensile load. The rod must not experience plastic deformation or an increase in length of more than 0.9 mm when a load of 24.5 kN is applied. Which of the four materials listed in table are possible candidates? Justify your answer. Material Elastic Modulus, GPa Yield Strength, MPa Tensile Strength, MPa 110 ETT 70 207 101 Copper Aluminum alloy Steel Brass alloy 248 255 448 345 289 420 551 420 * Plastic deformation is defined as a process in which the object due to applied force changes its size or shape in a way that is not reversible