A water pipe having a 2.29 cm inside diameter carries water into the basement of a house at a speed of 0.799 m/s and a pressure of235 kPa. If the pipe tapers to 1.89 cm and rises to the second floor 7.34 m above the input point, what are the (a) speed and (b) waterpressure at the second floor?(a) NumberiUnits(b) NumberiUnits

Answered: Image /qna-images/answer/96676a7b-a46c-475c-b853-7b084afb1c44.jpg

Answered: A water pipe having a 2.29 cm inside…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A U-shaped tube is filled with water of density 1000 kg/m3 until the level of the liquid is 28 cm above the bottom of the tube. Then oil of specific gravity 0.78 is poured into one branch of the tube until the level of the liquid in the other branch is 34 cm above the bottom of the tube. (g=9.8m/s2) I) Find the level of the oil-water interface in the branch where the oil was spilled II) Find the level of the oil-air interface in the branch where the oil was spilled
While filling up your car with gasoline, you notice that it takes 3 minutes to dispense 55 liters of gasoline through the 2.5 cm diameter hose. What is the average speed, in m/s, of the gasoline inside the hose?
Gardeners are holding a nozzle at the end of a hose to wash way mud from landscaping. The nozzle exit has a diameter of 10cm and the water is flowing at a rate of 12 m3/min. In this situation, what is the average water exit velocity and what is the horizontal resistance force required to hold the nozzle? Any help would be great
Vv
WHEN SEAWATER FLOWS INTO THE BOTTOM OPENING AT 10 M/S, CALCULATE THE VELOCITY OF THE SEAWATER LEVEL (8M ABOVE THE BOTTOM OF THE SUBMARINE) INSIDE THE BALLAST TANK (V ON DIAGRAM).
Prob6 conveyor belt discharges gravel into a barge as shown at a rate of 40 m³/min. If the gravel specific weight 18860 N/m³ 120 lbf, what is the tension in the hawser that secures the barge to the dock? Conveyor belt F-10 ft/s Hawser, Dock Gravel Barge Gravel 20⁰ +
Water is raised from a reservoir up 40 m to a storage tank through a 8 cm diameter pipe. If it is required to raise 27 liter per second, determine the horsepower input to a pump assuming that the pump is 75% efficient and that there is no friction loss in the pipe.(1 horsepower = 0.746 kW; density of water = 1000 kg/m3; dynamic viscosity = 1x10-3 Pa.s )
A horizontal pipe has an abrupt expansion from D₁ = 10 cm to D₂= 21 cm. The water velocity in the smaller section v1=13 m/s, and the flow is turbulent. If the pressure in the smaller section is P₁=250 kPa, then the velocity at the bigger pipe v2= m/s Water D1 V1 P1 D2 4
Water flows into a tank and out through another pipe, as shown in the figure below. The water in the tank has a surface area, Asurf = 5.6 m². At the bottom of the tank there is a door inclined at an angle = 45 degrees with respect to the horizontal. The door has a length L = 0.9 m and a width w=0.8 m (out of the page). The flowrate into the tank is Q₁ (t) = 0.3 m³/s and the flowrate out is Qo(t) = 0.07 m 3/5 At time t = 0, the water has a depth ho = 2 m. The density of water is p = 1000 kg/m³. Asurf x h(t) a) Find the pressure (in kilopascals) at time t = 0 Qout
Water with density of 998 kg/m3 flows from a lake through a device inside the building at rate of 0.11 m³/s as shown in figure below. The piping system has length and diameter of 91.5 m, 0.12 m respectively. ● (1) Is the device inside the building a pump or a turbine? Justify your answer. Determine the horsepower of the ● device. Neglect all minor losses and assume the friction factor is 0.025. Lake Int 10 m
A tea maker whose top (1 point) is open to the atmosphere is completely full. The tea flows from the tap with a hole diameter of 1 cm and the distance between the tap and the upper position is 12 cm. Calculate the flow rate (m3 / h) of the tea flowing from the tap. (Use of tea as concentrated water density)
Liquid fertiliser of density 1100 kg/m3 is being pumped along a pipe of diameter 15 cm at a constant rate of 5.25 kg/s. Calculate the average speed of the flow.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS