A waste management company handles large dumpsters of construction debris. The sorting process starts by downloading the dumpster from the transport truck and then dumping its contents into a large hopper as shown below. The waste management plant uses a hydraulic cylinder arrangement to tilt the dumpster to the point that the force of gravity will empty the contents. The plant operator activates an electric pump that pumps hydraulic oil into the input piston at an absolute pressure of 3.90 x 10° Pa and drives the output plunger, which has a radius of 0.140 m. If the design of the dumping arrangement is such that the output plunger remains perpendicular to the floor of the dumpster, determine the torque the plunger creates about an axis at the end of the dumpster. N m - dumpst 6,00 m- - output plunger rotation axis -input for hydraulic oil hopper

A waste management company handles large dumpsters of construction debris. The sorting process starts by downloading the dumpster from the transport truck and then dumping its contents into a large hopper as shown below. The waste management plant uses a hydraulic cylinder arrangement to tilt the dumpster to the point that the force of gravity will empty the contents. The plant operator activates an electric pump that pumps hydraulic oil into the input piston at an absolute pressure of 3.90 x 10° Pa and drives the output plunger, which has a radius of 0.140 m. If the design of the dumping arrangement is such that the output plunger remains perpendicular to the floor of the dumpster, determine the torque the plunger creates about an axis at the end of the dumpster. N m - dumpst 6,00 m- - output plunger rotation axis -input for hydraulic oil hopper

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

While taking a shower, you notice that the shower head is made up of 44 small round openings, each with a radius of 2.00 mm. You also determine that it takes 5.00 s for the shower to completely fill a 1.00-liter container you hold in the water stream. The water for the shower is pumped by a pump that is 5.50 m below the level of the shower head. The pump maintains an absolute pressure of 1.50 atm. Use g = 10 m/s2, and assume that 1 atmosphere is 1.0 105 Pa. (a) At what speed does the water emerge from the shower head? (b) What is the speed of the water in the pipe connected to the pump? (c) What is the cross-sectional area of the pipe connected to the pump?
A room has a width of 14.1 feet, a length of 15.5 feet, and a ceiling height of 12.0 ft. The average flow rate for this room's air conditioning unit is 3.07 m^3/s. How many SECONDS will it take for the air conditioner to cycle the volume of air in the room?
The drawing shows a hydsraulic chamber with a spring (string constant = 1250N/m) attached to the input piston and an object of 38 kg (resting on the output plunger). The piston and plunger are at the same height each having a negligible mass. By how much is the spring compressed from its unstrined position?
A 0.527 kg metal cylinder is placed inside the top of a plastic tube, the lower end of which is sealed off by an adjustable plunger. The cylinder comes to rest some distance above the plunger. The plastic tube has an inner radius of 6.56 mm and is frictionless. Neither the plunger nor the metal cylinder allow any air to flow around them. If the plunger is suddenly pushed upwards, increasing the pressure between the plunger and the metal cylinder by a factor of 1.35, what is the initial acceleration ? of the metal cylinder? Assume the pressure outside of the tube is 1.00 atmand that the top of the tube is open to the air.
A Volkswagen with mass m = 8.00 x 102kg is at rest as shown in the figure. Both pistons have a circular cross-sectional area. The small piston has a diameter of d1 = 0.25 m and the large piston has a diameter d2 = 4.5 m. Determine the magnitude of the forceexercised on the small piston.
Please don't provide handwritten solution .....
A moonshiner produces ethanol and stores it in a stainless tank in the form of a cylinder, 20 cm in diameter with a tight-fitting piston at the top. The total volumetric capacity of the tank is 0.20 m3 (200L). In an attempt to squeeze a little more into the tank. he piles lead bricks on the piston, the total mass of the bricks and piston is 120 kg. What additional volume of ethanol can he squeeze into the tank? Kethanol=11 x 10-10 Pa-1.
Assume that a raindrop has a volume of 0.05 cm^3 and you need an Avogadro's number of raindrops to fill up the cubic water tank. What is the length of the edge of the tank?
I need exam for my homework
A dump truck uses a hydraulic cylinder, as the drawing illustrates, to raise the trailer. A pump injects hydraulic oil into the cylinder (r = 15 cm) at an absolute pressure of 4 million Pascals. Initially as it starts to raise the trailer, what is the largest mass that could be lifted by this system? Assume atmospheric pressure = 1.01 x10^5 Pa
While taking a shower, you notice that the shower head is made up of 36 small round openings, each with a radius of 2.00 mm. You also determine that it takes 2.00 s for the shower to completely fi a 1.00-liter container you hold in the water stream. The water for the shower is pumped by a pump that is 5.60 m below the level of the shower head. The pump maintains an absolute pressure of 1.50 atm. Use g = 10 m/s?, and assume that 1 atmosphere is 1.0 x 105 Pa. (a) At what speed does the water emerge from the shower head? 1.105 m/s (b) What is the speed of the water in the pipe connected to the pump? m/s (c) What is the cross-sectional area of the pipe connected to the pump? m2
A 14,912-N car is raised using a hydraulic lift, which consists of a U-tube with arms of unequal areas, filled with incompressible oil and capped at both ends with tight-fitting pistons. The wider arm of the U-tube has a radius of 16 cm and the narrower arm has a radius of 8 cm. The car rests on the piston on the wider arm of the U-tube. The pistons are initially at the same level. What is the initial force in N that must be applied to the smaller piston in order to start lifting the car? (For purposes of this problem, you can neglect the weight of the pistons.) Express answer as a whole number.